/** ****************************************************************************** * @file stm32f3xx_hal_tim.c * @author MCD Application Team * @brief TIM HAL module driver. * This file provides firmware functions to manage the following * functionalities of the Timer (TIM) peripheral: * + Time Base Initialization * + Time Base Start * + Time Base Start Interruption * + Time Base Start DMA * + Time Output Compare/PWM Initialization * + Time Output Compare/PWM Channel Configuration * + Time Output Compare/PWM Start * + Time Output Compare/PWM Start Interruption * + Time Output Compare/PWM Start DMA * + Time Input Capture Initialization * + Time Input Capture Channel Configuration * + Time Input Capture Start * + Time Input Capture Start Interruption * + Time Input Capture Start DMA * + Time One Pulse Initialization * + Time One Pulse Channel Configuration * + Time One Pulse Start * + Time Encoder Interface Initialization * + Time Encoder Interface Start * + Time Encoder Interface Start Interruption * + Time Encoder Interface Start DMA * + Commutation Event configuration with Interruption and DMA * + Time OCRef clear configuration * + Time External Clock configuration @verbatim ============================================================================== ##### TIMER Generic features ##### ============================================================================== [..] The Timer features include: (#) 16-bit up, down, up/down auto-reload counter. (#) 16-bit programmable prescaler allowing dividing (also on the fly) the counter clock frequency either by any factor between 1 and 65536. (#) Up to 4 independent channels for: (++) Input Capture (++) Output Compare (++) PWM generation (Edge and Center-aligned Mode) (++) One-pulse mode output ##### How to use this driver ##### ============================================================================== [..] (#) Initialize the TIM low level resources by implementing the following functions depending from feature used : (++) Time Base : HAL_TIM_Base_MspInit() (++) Input Capture : HAL_TIM_IC_MspInit() (++) Output Compare : HAL_TIM_OC_MspInit() (++) PWM generation : HAL_TIM_PWM_MspInit() (++) One-pulse mode output : HAL_TIM_OnePulse_MspInit() (++) Encoder mode output : HAL_TIM_Encoder_MspInit() (#) Initialize the TIM low level resources : (##) Enable the TIM interface clock using __HAL_RCC_TIMx_CLK_ENABLE (); (##) TIM pins configuration (+++) Enable the clock for the TIM GPIOs using the following function: __HAL_RCC_GPIOx_CLK_ENABLE(); (+++) Configure these TIM pins in Alternate function mode using HAL_GPIO_Init(); (#) The external Clock can be configured, if needed (the default clock is the internal clock from the APBx), using the following function: HAL_TIM_ConfigClockSource, the clock configuration should be done before any start function. (#) Configure the TIM in the desired functioning mode using one of the Initialization function of this driver: (++) HAL_TIM_Base_Init: to use the Timer to generate a simple time base (++) HAL_TIM_OC_Init and HAL_TIM_OC_ConfigChannel: to use the Timer to generate an Output Compare signal. (++) HAL_TIM_PWM_Init and HAL_TIM_PWM_ConfigChannel: to use the Timer to generate a PWM signal. (++) HAL_TIM_IC_Init and HAL_TIM_IC_ConfigChannel: to use the Timer to measure an external signal. (++) HAL_TIM_OnePulse_Init and HAL_TIM_OnePulse_ConfigChannel: to use the Timer in One Pulse Mode. (++) HAL_TIM_Encoder_Init: to use the Timer Encoder Interface. (#) Activate the TIM peripheral using one of the start functions depending from the feature used: (++) Time Base : HAL_TIM_Base_Start(), HAL_TIM_Base_Start_DMA(), HAL_TIM_Base_Start_IT() (++) Input Capture : HAL_TIM_IC_Start(), HAL_TIM_IC_Start_DMA(), HAL_TIM_IC_Start_IT() (++) Output Compare : HAL_TIM_OC_Start(), HAL_TIM_OC_Start_DMA(), HAL_TIM_OC_Start_IT() (++) PWM generation : HAL_TIM_PWM_Start(), HAL_TIM_PWM_Start_DMA(), HAL_TIM_PWM_Start_IT() (++) One-pulse mode output : HAL_TIM_OnePulse_Start(), HAL_TIM_OnePulse_Start_IT() (++) Encoder mode output : HAL_TIM_Encoder_Start(), HAL_TIM_Encoder_Start_DMA(), HAL_TIM_Encoder_Start_IT(). (#) The DMA Burst is managed with the two following functions: HAL_TIM_DMABurst_WriteStart() HAL_TIM_DMABurst_ReadStart() @endverbatim ****************************************************************************** * @attention * *

© COPYRIGHT(c) 2016 STMicroelectronics

* * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ #include "stm32f3_hal.h" #include "stm32f3xx_hal_def.h" #include "stm32f3xx_hal_can.h" #include "stm32f3xx_hal_tim.h" /** @addtogroup STM32F3xx_HAL_Driver * @{ */ /** @defgroup TIM TIM * @brief TIM HAL module driver * @{ */ #define HAL_TIM_MODULE_ENABLED #ifdef HAL_TIM_MODULE_ENABLED /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private function prototypes -----------------------------------------------*/ /** @defgroup TIM_Private_Functions TIM Private Functions * @{ */ static void TIM_TI1_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter); static void TIM_TI2_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter); static void TIM_TI2_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter); static void TIM_TI3_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter); static void TIM_TI4_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter); static void TIM_ITRx_SetConfig(TIM_TypeDef* TIMx, uint16_t InputTriggerSource); static void TIM_DMAPeriodElapsedCplt(DMA_HandleTypeDef *hdma); static void TIM_DMATriggerCplt(DMA_HandleTypeDef *hdma); static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef *htim, TIM_SlaveConfigTypeDef * sSlaveConfig); /** * @} */ /* Exported functions ---------------------------------------------------------*/ /** @defgroup TIM_Exported_Functions TIM Exported Functions * @{ */ /** @defgroup TIM_Exported_Functions_Group1 Time Base functions * @brief Time Base functions * @verbatim ============================================================================== ##### Time Base functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM base. (+) De-initialize the TIM base. (+) Start the Time Base. (+) Stop the Time Base. (+) Start the Time Base and enable interrupt. (+) Stop the Time Base and disable interrupt. (+) Start the Time Base and enable DMA transfer. (+) Stop the Time Base and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM Time base Unit according to the specified * parameters in the TIM_HandleTypeDef and create the associated handle. * @param htim TIM Base handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Init(TIM_HandleTypeDef *htim) { /* Check the TIM handle allocation */ if(htim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); if(htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; /* Init the low level hardware : GPIO, CLOCK, NVIC */ HAL_TIM_Base_MspInit(htim); } /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Set the Time Base configuration */ TIM_Base_SetConfig(htim->Instance, &htim->Init); /* Initialize the TIM state*/ htim->State= HAL_TIM_STATE_READY; return HAL_OK; } /** * @brief DeInitializes the TIM Base peripheral * @param htim TIM Base handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_DeInit(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); htim->State = HAL_TIM_STATE_BUSY; /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ HAL_TIM_Base_MspDeInit(htim); /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM Base MSP. * @param htim TIM handle * @retval None */ __weak void HAL_TIM_Base_MspInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_Base_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Base MSP. * @param htim TIM handle * @retval None */ __weak void HAL_TIM_Base_MspDeInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_Base_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM Base generation. * @param htim TIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Start(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Change the TIM state*/ htim->State= HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Base generation. * @param htim TIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Stop(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the TIM state*/ htim->State= HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Base generation in interrupt mode. * @param htim TIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Start_IT(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); /* Enable the TIM Update interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_UPDATE); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Base generation in interrupt mode. * @param htim TIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Stop_IT(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); /* Disable the TIM Update interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_UPDATE); /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Base generation in DMA mode. * @param htim TIM handle * @param pData The source Buffer address. * @param Length The length of data to be transferred from memory to peripheral. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Start_DMA(TIM_HandleTypeDef *htim, uint32_t *pData, uint16_t Length) { /* Check the parameters */ assert_param(IS_TIM_DMA_INSTANCE(htim->Instance)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if((pData == 0U ) && (Length > 0U)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)pData, (uint32_t)&htim->Instance->ARR, Length); /* Enable the TIM Update DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_UPDATE); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Base generation in DMA mode. * @param htim TIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Base_Stop_DMA(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_DMA_INSTANCE(htim->Instance)); /* Disable the TIM Update DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_UPDATE); /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group2 Time Output Compare functions * @brief Time Output Compare functions * @verbatim ============================================================================== ##### Time Output Compare functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM Output Compare. (+) De-initialize the TIM Output Compare. (+) Start the Time Output Compare. (+) Stop the Time Output Compare. (+) Start the Time Output Compare and enable interrupt. (+) Stop the Time Output Compare and disable interrupt. (+) Start the Time Output Compare and enable DMA transfer. (+) Stop the Time Output Compare and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM Output Compare according to the specified * parameters in the TIM_HandleTypeDef and create the associated handle. * @param htim TIM Output Compare handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Init(TIM_HandleTypeDef* htim) { /* Check the TIM handle allocation */ if(htim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); if(htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_OC_MspInit(htim); } /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Init the base time for the Output Compare */ TIM_Base_SetConfig(htim->Instance, &htim->Init); /* Initialize the TIM state*/ htim->State= HAL_TIM_STATE_READY; return HAL_OK; } /** * @brief DeInitializes the TIM peripheral * @param htim TIM Output Compare handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_DeInit(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); htim->State = HAL_TIM_STATE_BUSY; /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); /* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */ HAL_TIM_OC_MspDeInit(htim); /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM Output Compare MSP. * @param htim TIM handle * @retval None */ __weak void HAL_TIM_OC_MspInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_OC_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Output Compare MSP. * @param htim TIM handle * @retval None */ __weak void HAL_TIM_OC_MspDeInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_OC_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM Output Compare signal generation. * @param htim TIM Output Compare handle * @param Channel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Start(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); /* Enable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Output Compare signal generation. * @param htim TIM handle * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); /* Disable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Ouput */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Output Compare signal generation in interrupt mode. * @param htim TIM OC handle * @param Channel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); } break; case TIM_CHANNEL_2: { /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); } break; case TIM_CHANNEL_3: { /* Enable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); } break; case TIM_CHANNEL_4: { /* Enable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4); } break; default: break; } /* Enable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Output Compare signal generation in interrupt mode. * @param htim TIM Output Compare handle * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); } break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); } break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); } break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4); } break; default: break; } /* Disable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Ouput */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Output Compare signal generation in DMA mode. * @param htim TIM Output Compare handle * @param Channel TIM Channel to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @param pData The source Buffer address. * @param Length The length of data to be transferred from memory to TIM peripheral * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if(((uint32_t)pData == 0U ) && (Length > 0U)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } switch (Channel) { case TIM_CHANNEL_1: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length); /* Enable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); } break; case TIM_CHANNEL_2: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length); /* Enable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); } break; case TIM_CHANNEL_3: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3,Length); /* Enable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); } break; case TIM_CHANNEL_4: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length); /* Enable the TIM Capture/Compare 4 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4); } break; default: break; } /* Enable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Output Compare signal generation in DMA mode. * @param htim TIM Output Compare handle * @param Channel TIM Channel to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OC_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Disable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); } break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); } break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); } break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4); } break; default: break; } /* Disable the Output compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Ouput */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group3 Time PWM functions * @brief Time PWM functions * @verbatim ============================================================================== ##### Time PWM functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM OPWM. (+) De-initialize the TIM PWM. (+) Start the Time PWM. (+) Stop the Time PWM. (+) Start the Time PWM and enable interrupt. (+) Stop the Time PWM and disable interrupt. (+) Start the Time PWM and enable DMA transfer. (+) Stop the Time PWM and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM PWM Time Base according to the specified * parameters in the TIM_HandleTypeDef and create the associated handle. * @param htim TIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Init(TIM_HandleTypeDef *htim) { /* Check the TIM handle allocation */ if(htim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); if(htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_PWM_MspInit(htim); } /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Init the base time for the PWM */ TIM_Base_SetConfig(htim->Instance, &htim->Init); /* Initialize the TIM state*/ htim->State= HAL_TIM_STATE_READY; return HAL_OK; } /** * @brief DeInitializes the TIM peripheral * @param htim TIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_DeInit(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); htim->State = HAL_TIM_STATE_BUSY; /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); /* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */ HAL_TIM_PWM_MspDeInit(htim); /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM PWM MSP. * @param htim TIM handle * @retval None */ __weak void HAL_TIM_PWM_MspInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_PWM_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM PWM MSP. * @param htim TIM handle * @retval None */ __weak void HAL_TIM_PWM_MspDeInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_PWM_MspDeInit could be implemented in the user file */ } /** * @brief Starts the PWM signal generation. * @param htim TIM handle * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Start(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the PWM signal generation. * @param htim TIM handle * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); /* Disable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Ouput */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Starts the PWM signal generation in interrupt mode. * @param htim TIM handle * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); } break; case TIM_CHANNEL_2: { /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); } break; case TIM_CHANNEL_3: { /* Enable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); } break; case TIM_CHANNEL_4: { /* Enable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4); } break; default: break; } /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the PWM signal generation in interrupt mode. * @param htim TIM handle * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Stop_IT (TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); } break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); } break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); } break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4); } break; default: break; } /* Disable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Ouput */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM PWM signal generation in DMA mode. * @param htim TIM handle * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @param pData The source Buffer address. * @param Length The length of data to be transferred from memory to TIM peripheral * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if(((uint32_t)pData == 0U ) && (Length > 0U)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } switch (Channel) { case TIM_CHANNEL_1: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)pData, (uint32_t)&htim->Instance->CCR1, Length); /* Enable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); } break; case TIM_CHANNEL_2: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)pData, (uint32_t)&htim->Instance->CCR2, Length); /* Enable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); } break; case TIM_CHANNEL_3: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)pData, (uint32_t)&htim->Instance->CCR3,Length); /* Enable the TIM Output Capture/Compare 3 request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); } break; case TIM_CHANNEL_4: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)pData, (uint32_t)&htim->Instance->CCR4, Length); /* Enable the TIM Capture/Compare 4 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4); } break; default: break; } /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM PWM signal generation in DMA mode. * @param htim TIM handle * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_PWM_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Disable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); } break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); } break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); } break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4); } break; default: break; } /* Disable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Ouput */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group4 Time Input Capture functions * @brief Time Input Capture functions * @verbatim ============================================================================== ##### Time Input Capture functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM Input Capture. (+) De-initialize the TIM Input Capture. (+) Start the Time Input Capture. (+) Stop the Time Input Capture. (+) Start the Time Input Capture and enable interrupt. (+) Stop the Time Input Capture and disable interrupt. (+) Start the Time Input Capture and enable DMA transfer. (+) Stop the Time Input Capture and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM Input Capture Time base according to the specified * parameters in the TIM_HandleTypeDef and create the associated handle. * @param htim TIM Input Capture handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Init(TIM_HandleTypeDef *htim) { /* Check the TIM handle allocation */ if(htim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); if(htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_IC_MspInit(htim); } /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Init the base time for the input capture */ TIM_Base_SetConfig(htim->Instance, &htim->Init); /* Initialize the TIM state*/ htim->State= HAL_TIM_STATE_READY; return HAL_OK; } /** * @brief DeInitializes the TIM peripheral * @param htim TIM Input Capture handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_DeInit(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); htim->State = HAL_TIM_STATE_BUSY; /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); /* DeInit the low level hardware: GPIO, CLOCK, NVIC and DMA */ HAL_TIM_IC_MspDeInit(htim); /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM Input Capture MSP. * @param htim TIM handle * @retval None */ __weak void HAL_TIM_IC_MspInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_IC_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Input Capture MSP. * @param htim TIM handle * @retval None */ __weak void HAL_TIM_IC_MspDeInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_IC_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM Input Capture measurement. * @param htim TIM Input Capture handle * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Start (TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); /* Enable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Input Capture measurement. * @param htim TIM handle * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); /* Disable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Input Capture measurement in interrupt mode. * @param htim TIM Input Capture handle * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Start_IT (TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); } break; case TIM_CHANNEL_2: { /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); } break; case TIM_CHANNEL_3: { /* Enable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC3); } break; case TIM_CHANNEL_4: { /* Enable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC4); } break; default: break; } /* Enable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Input Capture measurement in interrupt mode. * @param htim TIM handle * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); switch (Channel) { case TIM_CHANNEL_1: { /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); } break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); } break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC3); } break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC4); } break; default: break; } /* Disable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Input Capture measurement in DMA mode. * @param htim TIM Input Capture handle * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @param pData The destination Buffer address. * @param Length The length of data to be transferred from TIM peripheral to memory. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if((pData == 0U ) && (Length > 0U)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } switch (Channel) { case TIM_CHANNEL_1: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData, Length); /* Enable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); } break; case TIM_CHANNEL_2: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData, Length); /* Enable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); } break; case TIM_CHANNEL_3: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)&htim->Instance->CCR3, (uint32_t)pData, Length); /* Enable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC3); } break; case TIM_CHANNEL_4: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)&htim->Instance->CCR4, (uint32_t)pData, Length); /* Enable the TIM Capture/Compare 4 DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC4); } break; default: break; } /* Enable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Input Capture measurement in DMA mode. * @param htim TIM Input Capture handle * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CCX_INSTANCE(htim->Instance, Channel)); assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance)); switch (Channel) { case TIM_CHANNEL_1: { /* Disable the TIM Capture/Compare 1 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); } break; case TIM_CHANNEL_2: { /* Disable the TIM Capture/Compare 2 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); } break; case TIM_CHANNEL_3: { /* Disable the TIM Capture/Compare 3 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC3); } break; case TIM_CHANNEL_4: { /* Disable the TIM Capture/Compare 4 DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC4); } break; default: break; } /* Disable the Input Capture channel */ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_DISABLE); /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group5 Time One Pulse functions * @brief Time One Pulse functions * @verbatim ============================================================================== ##### Time One Pulse functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM One Pulse. (+) De-initialize the TIM One Pulse. (+) Start the Time One Pulse. (+) Stop the Time One Pulse. (+) Start the Time One Pulse and enable interrupt. (+) Stop the Time One Pulse and disable interrupt. (+) Start the Time One Pulse and enable DMA transfer. (+) Stop the Time One Pulse and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM One Pulse Time Base according to the specified * parameters in the TIM_HandleTypeDef and create the associated handle. * @param htim TIM OnePulse handle * @param OnePulseMode Select the One pulse mode. * This parameter can be one of the following values: * @arg TIM_OPMODE_SINGLE: Only one pulse will be generated. * @arg TIM_OPMODE_REPETITIVE: Repetitive pulses wil be generated. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_Init(TIM_HandleTypeDef *htim, uint32_t OnePulseMode) { /* Check the TIM handle allocation */ if(htim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); assert_param(IS_TIM_OPM_MODE(OnePulseMode)); assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); if(htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_OnePulse_MspInit(htim); } /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Configure the Time base in the One Pulse Mode */ TIM_Base_SetConfig(htim->Instance, &htim->Init); /* Reset the OPM Bit */ htim->Instance->CR1 &= ~TIM_CR1_OPM; /* Configure the OPM Mode */ htim->Instance->CR1 |= OnePulseMode; /* Initialize the TIM state*/ htim->State= HAL_TIM_STATE_READY; return HAL_OK; } /** * @brief DeInitializes the TIM One Pulse * @param htim TIM One Pulse handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_DeInit(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); htim->State = HAL_TIM_STATE_BUSY; /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ HAL_TIM_OnePulse_MspDeInit(htim); /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM One Pulse MSP. * @param htim TIM handle * @retval None */ __weak void HAL_TIM_OnePulse_MspInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_OnePulse_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM One Pulse MSP. * @param htim TIM handle * @retval None */ __weak void HAL_TIM_OnePulse_MspDeInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_OnePulse_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM One Pulse signal generation. * @param htim TIM One Pulse handle * @param OutputChannel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel) { /* Enable the Capture compare and the Input Capture channels (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be enabled together No need to enable the counter, it's enabled automatically by hardware (the counter starts in response to a stimulus and generate a pulse */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM One Pulse signal generation. * @param htim TIM One Pulse handle * @param OutputChannel TIM Channels to be disable * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel) { /* Disable the Capture compare and the Input Capture channels (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Ouput */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM One Pulse signal generation in interrupt mode. * @param htim TIM One Pulse handle * @param OutputChannel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel) { /* Enable the Capture compare and the Input Capture channels (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be enabled together No need to enable the counter, it's enabled automatically by hardware (the counter starts in response to a stimulus and generate a pulse */ /* Enable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); /* Enable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Enable the main output */ __HAL_TIM_MOE_ENABLE(htim); } /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM One Pulse signal generation in interrupt mode. * @param htim TIM One Pulse handle * @param OutputChannel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel) { /* Disable the TIM Capture/Compare 1 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); /* Disable the TIM Capture/Compare 2 interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); /* Disable the Capture compare and the Input Capture channels (in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); if(IS_TIM_BREAK_INSTANCE(htim->Instance) != RESET) { /* Disable the Main Ouput */ __HAL_TIM_MOE_DISABLE(htim); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group6 Time Encoder functions * @brief Time Encoder functions * @verbatim ============================================================================== ##### Time Encoder functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize and configure the TIM Encoder. (+) De-initialize the TIM Encoder. (+) Start the Time Encoder. (+) Stop the Time Encoder. (+) Start the Time Encoder and enable interrupt. (+) Stop the Time Encoder and disable interrupt. (+) Start the Time Encoder and enable DMA transfer. (+) Stop the Time Encoder and disable DMA transfer. @endverbatim * @{ */ /** * @brief Initializes the TIM Encoder Interface and create the associated handle. * @param htim TIM Encoder Interface handle * @param sConfig TIM Encoder Interface configuration structure * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Init(TIM_HandleTypeDef *htim, TIM_Encoder_InitTypeDef* sConfig) { uint32_t tmpsmcr = 0U; uint32_t tmpccmr1 = 0U; uint32_t tmpccer = 0U; /* Check the TIM handle allocation */ if(htim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); assert_param(IS_TIM_COUNTER_MODE(htim->Init.CounterMode)); assert_param(IS_TIM_CLOCKDIVISION_DIV(htim->Init.ClockDivision)); assert_param(IS_TIM_AUTORELOAD_PRELOAD(htim->Init.AutoReloadPreload)); assert_param(IS_TIM_ENCODER_MODE(sConfig->EncoderMode)); assert_param(IS_TIM_IC_SELECTION(sConfig->IC1Selection)); assert_param(IS_TIM_IC_SELECTION(sConfig->IC2Selection)); assert_param(IS_TIM_IC_POLARITY(sConfig->IC1Polarity)); assert_param(IS_TIM_IC_POLARITY(sConfig->IC2Polarity)); assert_param(IS_TIM_IC_PRESCALER(sConfig->IC1Prescaler)); assert_param(IS_TIM_IC_PRESCALER(sConfig->IC2Prescaler)); assert_param(IS_TIM_IC_FILTER(sConfig->IC1Filter)); assert_param(IS_TIM_IC_FILTER(sConfig->IC2Filter)); if(htim->State == HAL_TIM_STATE_RESET) { /* Allocate lock resource and initialize it */ htim->Lock = HAL_UNLOCKED; /* Init the low level hardware : GPIO, CLOCK, NVIC and DMA */ HAL_TIM_Encoder_MspInit(htim); } /* Set the TIM state */ htim->State= HAL_TIM_STATE_BUSY; /* Reset the SMS bits */ htim->Instance->SMCR &= ~TIM_SMCR_SMS; /* Configure the Time base in the Encoder Mode */ TIM_Base_SetConfig(htim->Instance, &htim->Init); /* Get the TIMx SMCR register value */ tmpsmcr = htim->Instance->SMCR; /* Get the TIMx CCMR1 register value */ tmpccmr1 = htim->Instance->CCMR1; /* Get the TIMx CCER register value */ tmpccer = htim->Instance->CCER; /* Set the encoder Mode */ tmpsmcr |= sConfig->EncoderMode; /* Select the Capture Compare 1 and the Capture Compare 2 as input */ tmpccmr1 &= ~(TIM_CCMR1_CC1S | TIM_CCMR1_CC2S); tmpccmr1 |= (sConfig->IC1Selection | (sConfig->IC2Selection << 8U)); /* Set the the Capture Compare 1 and the Capture Compare 2 prescalers and filters */ tmpccmr1 &= ~(TIM_CCMR1_IC1PSC | TIM_CCMR1_IC2PSC); tmpccmr1 &= ~(TIM_CCMR1_IC1F | TIM_CCMR1_IC2F); tmpccmr1 |= sConfig->IC1Prescaler | (sConfig->IC2Prescaler << 8U); tmpccmr1 |= (sConfig->IC1Filter << 4U) | (sConfig->IC2Filter << 12U); /* Set the TI1 and the TI2 Polarities */ tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC2P); tmpccer &= ~(TIM_CCER_CC1NP | TIM_CCER_CC2NP); tmpccer |= sConfig->IC1Polarity | (sConfig->IC2Polarity << 4U); /* Write to TIMx SMCR */ htim->Instance->SMCR = tmpsmcr; /* Write to TIMx CCMR1 */ htim->Instance->CCMR1 = tmpccmr1; /* Write to TIMx CCER */ htim->Instance->CCER = tmpccer; /* Initialize the TIM state*/ htim->State= HAL_TIM_STATE_READY; return HAL_OK; } /** * @brief DeInitializes the TIM Encoder interface * @param htim TIM Encoder handle * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_DeInit(TIM_HandleTypeDef *htim) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); htim->State = HAL_TIM_STATE_BUSY; /* Disable the TIM Peripheral Clock */ __HAL_TIM_DISABLE(htim); /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ HAL_TIM_Encoder_MspDeInit(htim); /* Change TIM state */ htim->State = HAL_TIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM Encoder Interface MSP. * @param htim TIM handle * @retval None */ __weak void HAL_TIM_Encoder_MspInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_Encoder_MspInit could be implemented in the user file */ } /** * @brief DeInitializes TIM Encoder Interface MSP. * @param htim TIM handle * @retval None */ __weak void HAL_TIM_Encoder_MspDeInit(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_Encoder_MspDeInit could be implemented in the user file */ } /** * @brief Starts the TIM Encoder Interface. * @param htim TIM Encoder Interface handle * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Start(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Enable the encoder interface channels */ switch (Channel) { case TIM_CHANNEL_1: { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); break; } case TIM_CHANNEL_2: { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); break; } default : { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); break; } } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Encoder Interface. * @param htim TIM Encoder Interface handle * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Stop(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Disable the Input Capture channels 1 and 2 (in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */ switch (Channel) { case TIM_CHANNEL_1: { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); break; } case TIM_CHANNEL_2: { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); break; } default : { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); break; } } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Encoder Interface in interrupt mode. * @param htim TIM Encoder Interface handle * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Enable the encoder interface channels */ /* Enable the capture compare Interrupts 1 and/or 2U */ switch (Channel) { case TIM_CHANNEL_1: { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); break; } case TIM_CHANNEL_2: { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); break; } default : { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1); __HAL_TIM_ENABLE_IT(htim, TIM_IT_CC2); break; } } /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Encoder Interface in interrupt mode. * @param htim TIM Encoder Interface handle * @param Channel TIM Channels to be disabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Disable the Input Capture channels 1 and 2 (in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */ if(Channel == TIM_CHANNEL_1) { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); /* Disable the capture compare Interrupts 1U */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); } else if(Channel == TIM_CHANNEL_2) { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); /* Disable the capture compare Interrupts 2U */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); } else { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); /* Disable the capture compare Interrupts 1 and 2U */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC1); __HAL_TIM_DISABLE_IT(htim, TIM_IT_CC2); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Starts the TIM Encoder Interface in DMA mode. * @param htim TIM Encoder Interface handle * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected * @param pData1: The destination Buffer address for IC1. * @param pData2: The destination Buffer address for IC2. * @param Length The length of data to be transferred from TIM peripheral to memory. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData1, uint32_t *pData2, uint16_t Length) { /* Check the parameters */ assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if((((pData1 == 0U) || (pData2 == 0U) )) && (Length > 0U)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } switch (Channel) { case TIM_CHANNEL_1: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t )pData1, Length); /* Enable the TIM Input Capture DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); } break; case TIM_CHANNEL_2: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData2, Length); /* Enable the TIM Input Capture DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); } break; case TIM_CHANNEL_ALL: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->CCR1, (uint32_t)pData1, Length); /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->CCR2, (uint32_t)pData2, Length); /* Enable the Peripheral */ __HAL_TIM_ENABLE(htim); /* Enable the Capture compare channel */ TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_ENABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_ENABLE); /* Enable the TIM Input Capture DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC1); /* Enable the TIM Input Capture DMA request */ __HAL_TIM_ENABLE_DMA(htim, TIM_DMA_CC2); } break; default: break; } /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM Encoder Interface in DMA mode. * @param htim TIM Encoder Interface handle * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_ALL: TIM Channel 1 and TIM Channel 2 are selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_Encoder_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_DMA_CC_INSTANCE(htim->Instance)); /* Disable the Input Capture channels 1 and 2 (in the EncoderInterface the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2) */ if(Channel == TIM_CHANNEL_1) { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); /* Disable the capture compare DMA Request 1U */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); } else if(Channel == TIM_CHANNEL_2) { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); /* Disable the capture compare DMA Request 2U */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); } else { TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE); TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE); /* Disable the capture compare DMA Request 1 and 2U */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC1); __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_CC2); } /* Disable the Peripheral */ __HAL_TIM_DISABLE(htim); /* Change the htim state */ htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group7 TIM IRQ handler management * @brief IRQ handler management * @verbatim ============================================================================== ##### IRQ handler management ##### ============================================================================== [..] This section provides Timer IRQ handler function. @endverbatim * @{ */ /** * @brief This function handles TIM interrupts requests. * @param htim TIM handle * @retval None */ void HAL_TIM_IRQHandler(TIM_HandleTypeDef *htim) { /* Capture compare 1 event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC1) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_CC1) !=RESET) { { __HAL_TIM_CLEAR_FLAG(htim, TIM_FLAG_CC1); htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1; /* Input capture event */ if((htim->Instance->CCMR1 & TIM_CCMR1_CC1S) != 0x00U) { HAL_TIM_IC_CaptureCallback(htim); } /* Output compare event */ else { HAL_TIM_OC_DelayElapsedCallback(htim); HAL_TIM_PWM_PulseFinishedCallback(htim); } htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } } } /* Capture compare 2 event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC2) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_CC2) !=RESET) { __HAL_TIM_CLEAR_FLAG(htim, TIM_FLAG_CC2); htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2; /* Input capture event */ if((htim->Instance->CCMR1 & TIM_CCMR1_CC2S) != 0x00U) { HAL_TIM_IC_CaptureCallback(htim); } /* Output compare event */ else { HAL_TIM_OC_DelayElapsedCallback(htim); HAL_TIM_PWM_PulseFinishedCallback(htim); } htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } } /* Capture compare 3 event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC3) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_CC3) !=RESET) { __HAL_TIM_CLEAR_FLAG(htim, TIM_FLAG_CC3); htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3; /* Input capture event */ if((htim->Instance->CCMR2 & TIM_CCMR2_CC3S) != 0x00U) { HAL_TIM_IC_CaptureCallback(htim); } /* Output compare event */ else { HAL_TIM_OC_DelayElapsedCallback(htim); HAL_TIM_PWM_PulseFinishedCallback(htim); } htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } } /* Capture compare 4 event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_CC4) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_CC4) !=RESET) { __HAL_TIM_CLEAR_FLAG(htim, TIM_FLAG_CC4); htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4; /* Input capture event */ if((htim->Instance->CCMR2 & TIM_CCMR2_CC4S) != 0x00U) { HAL_TIM_IC_CaptureCallback(htim); } /* Output compare event */ else { HAL_TIM_OC_DelayElapsedCallback(htim); HAL_TIM_PWM_PulseFinishedCallback(htim); } htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } } /* TIM Update event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_UPDATE) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_UPDATE) !=RESET) { __HAL_TIM_CLEAR_FLAG(htim, TIM_FLAG_UPDATE); HAL_TIM_PeriodElapsedCallback(htim); } } /* TIM Break input event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_BREAK) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_BREAK) !=RESET) { __HAL_TIM_CLEAR_FLAG(htim, TIM_FLAG_BREAK); HAL_TIMEx_BreakCallback(htim); } } #if defined(TIM_FLAG_BREAK2) /* TIM Break input 2 event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_BREAK2) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_BREAK) !=RESET) { __HAL_TIM_CLEAR_FLAG(htim, TIM_FLAG_BREAK2); HAL_TIMEx_Break2Callback(htim); } } #endif /* TIM Trigger detection event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_TRIGGER) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_TRIGGER) !=RESET) { __HAL_TIM_CLEAR_FLAG(htim, TIM_FLAG_TRIGGER); HAL_TIM_TriggerCallback(htim); } } /* TIM commutation event */ if(__HAL_TIM_GET_FLAG(htim, TIM_FLAG_COM) != RESET) { if(__HAL_TIM_GET_IT_SOURCE(htim, TIM_IT_COM) !=RESET) { __HAL_TIM_CLEAR_FLAG(htim, TIM_FLAG_COM); HAL_TIMEx_CommutationCallback(htim); } } } /** * @} */ /** @defgroup TIM_Exported_Functions_Group8 Peripheral Control functions * @brief Peripheral Control functions * @verbatim ============================================================================== ##### Peripheral Control functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Configure The Input Output channels for OC, PWM, IC or One Pulse mode. (+) Configure External Clock source. (+) Configure Complementary channels, break features and dead time. (+) Configure Master and the Slave synchronization. (+) Configure the DMA Burst Mode. @endverbatim * @{ */ /** * @brief Initializes the TIM Output Compare Channels according to the specified * parameters in the TIM_OC_InitTypeDef. * @param htim TIM Output Compare handle * @param sConfig TIM Output Compare configuration structure * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ __weak HAL_StatusTypeDef HAL_TIM_OC_ConfigChannel(TIM_HandleTypeDef *htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CHANNELS(Channel)); assert_param(IS_TIM_OC_MODE(sConfig->OCMode)); assert_param(IS_TIM_OC_POLARITY(sConfig->OCPolarity)); /* Check input state */ __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; switch (Channel) { case TIM_CHANNEL_1: { assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); /* Configure the TIM Channel 1 in Output Compare */ TIM_OC1_SetConfig(htim->Instance, sConfig); } break; case TIM_CHANNEL_2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Configure the TIM Channel 2 in Output Compare */ TIM_OC2_SetConfig(htim->Instance, sConfig); } break; case TIM_CHANNEL_3: { assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); /* Configure the TIM Channel 3 in Output Compare */ TIM_OC3_SetConfig(htim->Instance, sConfig); } break; case TIM_CHANNEL_4: { assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); /* Configure the TIM Channel 4 in Output Compare */ TIM_OC4_SetConfig(htim->Instance, sConfig); } break; default: break; } htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM Input Capture Channels according to the specified * parameters in the TIM_IC_InitTypeDef. * @param htim TIM IC handle * @param sConfig TIM Input Capture configuration structure * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_IC_ConfigChannel(TIM_HandleTypeDef *htim, TIM_IC_InitTypeDef* sConfig, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); assert_param(IS_TIM_IC_POLARITY(sConfig->ICPolarity)); assert_param(IS_TIM_IC_SELECTION(sConfig->ICSelection)); assert_param(IS_TIM_IC_PRESCALER(sConfig->ICPrescaler)); assert_param(IS_TIM_IC_FILTER(sConfig->ICFilter)); __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; if (Channel == TIM_CHANNEL_1) { /* TI1 Configuration */ TIM_TI1_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); /* Reset the IC1PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC; /* Set the IC1PSC value */ htim->Instance->CCMR1 |= sConfig->ICPrescaler; } else if (Channel == TIM_CHANNEL_2) { /* TI2 Configuration */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); TIM_TI2_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); /* Reset the IC2PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC2PSC; /* Set the IC2PSC value */ htim->Instance->CCMR1 |= (sConfig->ICPrescaler << 8U); } else if (Channel == TIM_CHANNEL_3) { /* TI3 Configuration */ assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); TIM_TI3_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); /* Reset the IC3PSC Bits */ htim->Instance->CCMR2 &= ~TIM_CCMR2_IC3PSC; /* Set the IC3PSC value */ htim->Instance->CCMR2 |= sConfig->ICPrescaler; } else { /* TI4 Configuration */ assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); TIM_TI4_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); /* Reset the IC4PSC Bits */ htim->Instance->CCMR2 &= ~TIM_CCMR2_IC4PSC; /* Set the IC4PSC value */ htim->Instance->CCMR2 |= (sConfig->ICPrescaler << 8U); } htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM PWM channels according to the specified * parameters in the TIM_OC_InitTypeDef. * @param htim TIM handle * @param sConfig TIM PWM configuration structure * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval HAL status */ __weak HAL_StatusTypeDef HAL_TIM_PWM_ConfigChannel(TIM_HandleTypeDef *htim, TIM_OC_InitTypeDef* sConfig, uint32_t Channel) { __HAL_LOCK(htim); /* Check the parameters */ assert_param(IS_TIM_CHANNELS(Channel)); assert_param(IS_TIM_PWM_MODE(sConfig->OCMode)); assert_param(IS_TIM_OC_POLARITY(sConfig->OCPolarity)); assert_param(IS_TIM_FAST_STATE(sConfig->OCFastMode)); htim->State = HAL_TIM_STATE_BUSY; switch (Channel) { case TIM_CHANNEL_1: { assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); /* Configure the Channel 1 in PWM mode */ TIM_OC1_SetConfig(htim->Instance, sConfig); /* Set the Preload enable bit for channel1 */ htim->Instance->CCMR1 |= TIM_CCMR1_OC1PE; /* Configure the Output Fast mode */ htim->Instance->CCMR1 &= ~TIM_CCMR1_OC1FE; htim->Instance->CCMR1 |= sConfig->OCFastMode; } break; case TIM_CHANNEL_2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Configure the Channel 2 in PWM mode */ TIM_OC2_SetConfig(htim->Instance, sConfig); /* Set the Preload enable bit for channel2 */ htim->Instance->CCMR1 |= TIM_CCMR1_OC2PE; /* Configure the Output Fast mode */ htim->Instance->CCMR1 &= ~TIM_CCMR1_OC2FE; htim->Instance->CCMR1 |= sConfig->OCFastMode << 8U; } break; case TIM_CHANNEL_3: { assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); /* Configure the Channel 3 in PWM mode */ TIM_OC3_SetConfig(htim->Instance, sConfig); /* Set the Preload enable bit for channel3 */ htim->Instance->CCMR2 |= TIM_CCMR2_OC3PE; /* Configure the Output Fast mode */ htim->Instance->CCMR2 &= ~TIM_CCMR2_OC3FE; htim->Instance->CCMR2 |= sConfig->OCFastMode; } break; case TIM_CHANNEL_4: { assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); /* Configure the Channel 4 in PWM mode */ TIM_OC4_SetConfig(htim->Instance, sConfig); /* Set the Preload enable bit for channel4 */ htim->Instance->CCMR2 |= TIM_CCMR2_OC4PE; /* Configure the Output Fast mode */ htim->Instance->CCMR2 &= ~TIM_CCMR2_OC4FE; htim->Instance->CCMR2 |= sConfig->OCFastMode << 8U; } break; default: break; } htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Initializes the TIM One Pulse Channels according to the specified * parameters in the TIM_OnePulse_InitTypeDef. * @param htim TIM One Pulse handle * @param sConfig TIM One Pulse configuration structure * @param OutputChannel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @param InputChannel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_OnePulse_ConfigChannel(TIM_HandleTypeDef *htim, TIM_OnePulse_InitTypeDef* sConfig, uint32_t OutputChannel, uint32_t InputChannel) { TIM_OC_InitTypeDef temp1; /* Check the parameters */ assert_param(IS_TIM_OPM_CHANNELS(OutputChannel)); assert_param(IS_TIM_OPM_CHANNELS(InputChannel)); if(OutputChannel != InputChannel) { __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; /* Extract the Ouput compare configuration from sConfig structure */ temp1.OCMode = sConfig->OCMode; temp1.Pulse = sConfig->Pulse; temp1.OCPolarity = sConfig->OCPolarity; temp1.OCNPolarity = sConfig->OCNPolarity; temp1.OCIdleState = sConfig->OCIdleState; temp1.OCNIdleState = sConfig->OCNIdleState; switch (OutputChannel) { case TIM_CHANNEL_1: { assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); TIM_OC1_SetConfig(htim->Instance, &temp1); } break; case TIM_CHANNEL_2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); TIM_OC2_SetConfig(htim->Instance, &temp1); } break; default: break; } switch (InputChannel) { case TIM_CHANNEL_1: { assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); TIM_TI1_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); /* Reset the IC1PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC1PSC; /* Select the Trigger source */ htim->Instance->SMCR &= ~TIM_SMCR_TS; htim->Instance->SMCR |= TIM_TS_TI1FP1; /* Select the Slave Mode */ htim->Instance->SMCR &= ~TIM_SMCR_SMS; htim->Instance->SMCR |= TIM_SLAVEMODE_TRIGGER; } break; case TIM_CHANNEL_2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); TIM_TI2_SetConfig(htim->Instance, sConfig->ICPolarity, sConfig->ICSelection, sConfig->ICFilter); /* Reset the IC2PSC Bits */ htim->Instance->CCMR1 &= ~TIM_CCMR1_IC2PSC; /* Select the Trigger source */ htim->Instance->SMCR &= ~TIM_SMCR_TS; htim->Instance->SMCR |= TIM_TS_TI2FP2; /* Select the Slave Mode */ htim->Instance->SMCR &= ~TIM_SMCR_SMS; htim->Instance->SMCR |= TIM_SLAVEMODE_TRIGGER; } break; default: break; } htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } else { return HAL_ERROR; } } /** * @brief Configure the DMA Burst to transfer Data from the memory to the TIM peripheral * @param htim TIM handle * @param BurstBaseAddress TIM Base address from where the DMA will start the Data write * This parameter can be one of the following values: * @arg TIM_DMABASE_CR1 * @arg TIM_DMABASE_CR2 * @arg TIM_DMABASE_SMCR * @arg TIM_DMABASE_DIER * @arg TIM_DMABASE_SR * @arg TIM_DMABASE_EGR * @arg TIM_DMABASE_CCMR1 * @arg TIM_DMABASE_CCMR2 * @arg TIM_DMABASE_CCER * @arg TIM_DMABASE_CNT * @arg TIM_DMABASE_PSC * @arg TIM_DMABASE_ARR * @arg TIM_DMABASE_RCR * @arg TIM_DMABASE_CCR1 * @arg TIM_DMABASE_CCR2 * @arg TIM_DMABASE_CCR3 * @arg TIM_DMABASE_CCR4 * @arg TIM_DMABASE_BDTR * @arg TIM_DMABASE_DCR * @param BurstRequestSrc TIM DMA Request sources * This parameter can be one of the following values: * @arg TIM_DMA_UPDATE: TIM update Interrupt source * @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source * @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source * @arg TIM_DMA_CC3: TIM Capture Compare 3 DMA source * @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source * @arg TIM_DMA_COM: TIM Commutation DMA source * @arg TIM_DMA_TRIGGER: TIM Trigger DMA source * @param BurstBuffer The Buffer address. * @param BurstLength DMA Burst length. This parameter can be one value * between: TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStart(TIM_HandleTypeDef *htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc, uint32_t *BurstBuffer, uint32_t BurstLength) { return HAL_TIM_DMABurst_MultiWriteStart(htim, BurstBaseAddress, BurstRequestSrc, BurstBuffer, BurstLength, ((BurstLength) >> 8U) + 1U); } /** * @brief Configure the DMA Burst to transfer multiple Data from the memory to the TIM peripheral * @param htim TIM handle * @param BurstBaseAddress TIM Base address from where the DMA will start the Data write * This parameter can be one of the following values: * @arg TIM_DMABASE_CR1 * @arg TIM_DMABASE_CR2 * @arg TIM_DMABASE_SMCR * @arg TIM_DMABASE_DIER * @arg TIM_DMABASE_SR * @arg TIM_DMABASE_EGR * @arg TIM_DMABASE_CCMR1 * @arg TIM_DMABASE_CCMR2 * @arg TIM_DMABASE_CCER * @arg TIM_DMABASE_CNT * @arg TIM_DMABASE_PSC * @arg TIM_DMABASE_ARR * @arg TIM_DMABASE_RCR * @arg TIM_DMABASE_CCR1 * @arg TIM_DMABASE_CCR2 * @arg TIM_DMABASE_CCR3 * @arg TIM_DMABASE_CCR4 * @arg TIM_DMABASE_BDTR * @arg TIM_DMABASE_DCR * @param BurstRequestSrc TIM DMA Request sources * This parameter can be one of the following values: * @arg TIM_DMA_UPDATE: TIM update Interrupt source * @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source * @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source * @arg TIM_DMA_CC3: TIM Capture Compare 3 DMA source * @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source * @arg TIM_DMA_COM: TIM Commutation DMA source * @arg TIM_DMA_TRIGGER: TIM Trigger DMA source * @param BurstBuffer The Buffer address. * @param BurstLength DMA Burst length. This parameter can be one value * between: TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS. * @param DataLength Data length. This parameter can be one value * between 1 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_MultiWriteStart(TIM_HandleTypeDef *htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc, uint32_t* BurstBuffer, uint32_t BurstLength, uint32_t DataLength) { /* Check the parameters */ assert_param(IS_TIM_DMABURST_INSTANCE(htim->Instance)); assert_param(IS_TIM_DMA_BASE(BurstBaseAddress)); assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc)); assert_param(IS_TIM_DMA_LENGTH(BurstLength)); assert_param(IS_TIM_DMA_DATA_LENGTH(DataLength)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if((BurstBuffer == 0U ) && (BurstLength > 0U)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } switch(BurstRequestSrc) { case TIM_DMA_UPDATE: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, DataLength); } break; case TIM_DMA_CC1: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, DataLength); } break; case TIM_DMA_CC2: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, DataLength); } break; case TIM_DMA_CC3: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, DataLength); } break; case TIM_DMA_CC4: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMADelayPulseCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, DataLength); } break; case TIM_DMA_COM: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = TIMEx_DMACommutationCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_COMMUTATION], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, DataLength); } break; case TIM_DMA_TRIGGER: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_TRIGGER]->XferCpltCallback = TIM_DMATriggerCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_TRIGGER]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_TRIGGER], (uint32_t)BurstBuffer, (uint32_t)&htim->Instance->DMAR, DataLength); } break; default: break; } /* configure the DMA Burst Mode */ htim->Instance->DCR = BurstBaseAddress | BurstLength; /* Enable the TIM DMA Request */ __HAL_TIM_ENABLE_DMA(htim, BurstRequestSrc); htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stops the TIM DMA Burst mode * @param htim TIM handle * @param BurstRequestSrc TIM DMA Request sources to disable * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_WriteStop(TIM_HandleTypeDef *htim, uint32_t BurstRequestSrc) { /* Check the parameters */ assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc)); /* Abort the DMA transfer (at least disable the DMA channel) */ switch(BurstRequestSrc) { case TIM_DMA_UPDATE: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_UPDATE]); } break; case TIM_DMA_CC1: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC1]); } break; case TIM_DMA_CC2: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC2]); } break; case TIM_DMA_CC3: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC3]); } break; case TIM_DMA_CC4: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC4]); } break; case TIM_DMA_COM: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_COMMUTATION]); } break; case TIM_DMA_TRIGGER: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_TRIGGER]); } break; default: break; } /* Disable the TIM Update DMA request */ __HAL_TIM_DISABLE_DMA(htim, BurstRequestSrc); /* Return function status */ return HAL_OK; } /** * @brief Configure the DMA Burst to transfer Data from the TIM peripheral to the memory * @param htim TIM handle * @param BurstBaseAddress TIM Base address from where the DMA will starts the Data read * This parameter can be one of the following values: * @arg TIM_DMABASE_CR1 * @arg TIM_DMABASE_CR2 * @arg TIM_DMABASE_SMCR * @arg TIM_DMABASE_DIER * @arg TIM_DMABASE_SR * @arg TIM_DMABASE_EGR * @arg TIM_DMABASE_CCMR1 * @arg TIM_DMABASE_CCMR2 * @arg TIM_DMABASE_CCER * @arg TIM_DMABASE_CNT * @arg TIM_DMABASE_PSC * @arg TIM_DMABASE_ARR * @arg TIM_DMABASE_RCR * @arg TIM_DMABASE_CCR1 * @arg TIM_DMABASE_CCR2 * @arg TIM_DMABASE_CCR3 * @arg TIM_DMABASE_CCR4 * @arg TIM_DMABASE_BDTR * @arg TIM_DMABASE_DCR * @param BurstRequestSrc TIM DMA Request sources * This parameter can be one of the following values: * @arg TIM_DMA_UPDATE: TIM update Interrupt source * @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source * @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source * @arg TIM_DMA_CC3: TIM Capture Compare 3 DMA source * @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source * @arg TIM_DMA_COM: TIM Commutation DMA source * @arg TIM_DMA_TRIGGER: TIM Trigger DMA source * @param BurstBuffer The Buffer address. * @param BurstLength DMA Burst length. This parameter can be one value * between: TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStart(TIM_HandleTypeDef *htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc, uint32_t *BurstBuffer, uint32_t BurstLength) { return HAL_TIM_DMABurst_MultiReadStart(htim, BurstBaseAddress, BurstRequestSrc, BurstBuffer, BurstLength, ((BurstLength) >> 8U) + 1U); } /** * @brief Configure the DMA Burst to transfer multiple Data from the TIM peripheral to the memory * @param htim TIM handle * @param BurstBaseAddress TIM Base address from where the DMA will starts the Data read * This parameter can be one of the following values: * @arg TIM_DMABASE_CR1 * @arg TIM_DMABASE_CR2 * @arg TIM_DMABASE_SMCR * @arg TIM_DMABASE_DIER * @arg TIM_DMABASE_SR * @arg TIM_DMABASE_EGR * @arg TIM_DMABASE_CCMR1 * @arg TIM_DMABASE_CCMR2 * @arg TIM_DMABASE_CCER * @arg TIM_DMABASE_CNT * @arg TIM_DMABASE_PSC * @arg TIM_DMABASE_ARR * @arg TIM_DMABASE_RCR * @arg TIM_DMABASE_CCR1 * @arg TIM_DMABASE_CCR2 * @arg TIM_DMABASE_CCR3 * @arg TIM_DMABASE_CCR4 * @arg TIM_DMABASE_BDTR * @arg TIM_DMABASE_DCR * @param BurstRequestSrc TIM DMA Request sources * This parameter can be one of the following values: * @arg TIM_DMA_UPDATE: TIM update Interrupt source * @arg TIM_DMA_CC1: TIM Capture Compare 1 DMA source * @arg TIM_DMA_CC2: TIM Capture Compare 2 DMA source * @arg TIM_DMA_CC3: TIM Capture Compare 3 DMA source * @arg TIM_DMA_CC4: TIM Capture Compare 4 DMA source * @arg TIM_DMA_COM: TIM Commutation DMA source * @arg TIM_DMA_TRIGGER: TIM Trigger DMA source * @param BurstBuffer The Buffer address. * @param BurstLength DMA Burst length. This parameter can be one value * between: TIM_DMABURSTLENGTH_1TRANSFER and TIM_DMABURSTLENGTH_18TRANSFERS. * @param DataLength Data length. This parameter can be one value * between 1 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_MultiReadStart(TIM_HandleTypeDef *htim, uint32_t BurstBaseAddress, uint32_t BurstRequestSrc, uint32_t *BurstBuffer, uint32_t BurstLength, uint32_t DataLength) { /* Check the parameters */ assert_param(IS_TIM_DMABURST_INSTANCE(htim->Instance)); assert_param(IS_TIM_DMA_BASE(BurstBaseAddress)); assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc)); assert_param(IS_TIM_DMA_LENGTH(BurstLength)); assert_param(IS_TIM_DMA_DATA_LENGTH(DataLength)); if((htim->State == HAL_TIM_STATE_BUSY)) { return HAL_BUSY; } else if((htim->State == HAL_TIM_STATE_READY)) { if((BurstBuffer == 0U ) && (BurstLength > 0U)) { return HAL_ERROR; } else { htim->State = HAL_TIM_STATE_BUSY; } } switch(BurstRequestSrc) { case TIM_DMA_UPDATE: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferCpltCallback = TIM_DMAPeriodElapsedCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_UPDATE]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_UPDATE], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, DataLength); } break; case TIM_DMA_CC1: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC1]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC1]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC1], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, DataLength); } break; case TIM_DMA_CC2: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC2]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC2]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC2], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, DataLength); } break; case TIM_DMA_CC3: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC3]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC3]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC3], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, DataLength); } break; case TIM_DMA_CC4: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_CC4]->XferCpltCallback = TIM_DMACaptureCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_CC4]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_CC4], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, DataLength); } break; case TIM_DMA_COM: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferCpltCallback = TIMEx_DMACommutationCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_COMMUTATION]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_COMMUTATION], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, DataLength); } break; case TIM_DMA_TRIGGER: { /* Set the DMA Period elapsed callback */ htim->hdma[TIM_DMA_ID_TRIGGER]->XferCpltCallback = TIM_DMATriggerCplt; /* Set the DMA error callback */ htim->hdma[TIM_DMA_ID_TRIGGER]->XferErrorCallback = TIM_DMAError ; /* Enable the DMA channel */ HAL_DMA_Start_IT(htim->hdma[TIM_DMA_ID_TRIGGER], (uint32_t)&htim->Instance->DMAR, (uint32_t)BurstBuffer, DataLength); } break; default: break; } /* configure the DMA Burst Mode */ htim->Instance->DCR = BurstBaseAddress | BurstLength; /* Enable the TIM DMA Request */ __HAL_TIM_ENABLE_DMA(htim, BurstRequestSrc); htim->State = HAL_TIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the DMA burst reading * @param htim TIM handle * @param BurstRequestSrc TIM DMA Request sources to disable. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_DMABurst_ReadStop(TIM_HandleTypeDef *htim, uint32_t BurstRequestSrc) { /* Check the parameters */ assert_param(IS_TIM_DMA_SOURCE(BurstRequestSrc)); /* Abort the DMA transfer (at least disable the DMA channel) */ switch(BurstRequestSrc) { case TIM_DMA_UPDATE: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_UPDATE]); } break; case TIM_DMA_CC1: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC1]); } break; case TIM_DMA_CC2: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC2]); } break; case TIM_DMA_CC3: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC3]); } break; case TIM_DMA_CC4: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_CC4]); } break; case TIM_DMA_COM: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_COMMUTATION]); } break; case TIM_DMA_TRIGGER: { HAL_DMA_Abort(htim->hdma[TIM_DMA_ID_TRIGGER]); } break; default: break; } /* Disable the TIM Update DMA request */ __HAL_TIM_DISABLE_DMA(htim, BurstRequestSrc); /* Return function status */ return HAL_OK; } /** * @brief Generate a software event * @param htim TIM handle * @param EventSource specifies the event source. * This parameter can be one of the following values: * @arg TIM_EVENTSOURCE_UPDATE: Timer update Event source * @arg TIM_EVENTSOURCE_CC1: Timer Capture Compare 1 Event source * @arg TIM_EVENTSOURCE_CC2: Timer Capture Compare 2 Event source * @arg TIM_EVENTSOURCE_CC3: Timer Capture Compare 3 Event source * @arg TIM_EVENTSOURCE_CC4: Timer Capture Compare 4 Event source * @arg TIM_EVENTSOURCE_COM: Timer COM event source * @arg TIM_EVENTSOURCE_TRIGGER: Timer Trigger Event source * @arg TIM_EVENTSOURCE_BREAK: Timer Break event source * @arg TIM_EVENTSOURCE_BREAK2: Timer Break2 event source * @retval HAL status * @note TIM_EVENTSOURCE_BREAK2 isn't relevant for STM32F37xx and STM32F38xx * devices */ HAL_StatusTypeDef HAL_TIM_GenerateEvent(TIM_HandleTypeDef *htim, uint32_t EventSource) { /* Check the parameters */ assert_param(IS_TIM_INSTANCE(htim->Instance)); assert_param(IS_TIM_EVENT_SOURCE(EventSource)); /* Process Locked */ __HAL_LOCK(htim); /* Change the TIM state */ htim->State = HAL_TIM_STATE_BUSY; /* Set the event sources */ htim->Instance->EGR = EventSource; /* Change the TIM state */ htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); /* Return function status */ return HAL_OK; } /** * @brief Configures the OCRef clear feature * @param htim TIM handle * @param sClearInputConfig pointer to a TIM_ClearInputConfigTypeDef structure that * contains the OCREF clear feature and parameters for the TIM peripheral. * @param Channel specifies the TIM Channel * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 * @arg TIM_CHANNEL_2: TIM Channel 2 * @arg TIM_CHANNEL_3: TIM Channel 3 * @arg TIM_CHANNEL_4: TIM Channel 4 * @retval HAL status */ __weak HAL_StatusTypeDef HAL_TIM_ConfigOCrefClear(TIM_HandleTypeDef *htim, TIM_ClearInputConfigTypeDef * sClearInputConfig, uint32_t Channel) { /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); assert_param(IS_TIM_CHANNELS(Channel)); assert_param(IS_TIM_CLEARINPUT_SOURCE(sClearInputConfig->ClearInputSource)); /* Process Locked */ __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; if(sClearInputConfig->ClearInputSource == TIM_CLEARINPUTSOURCE_ETR) { /* Check the parameters */ assert_param(IS_TIM_CLEARINPUT_POLARITY(sClearInputConfig->ClearInputPolarity)); assert_param(IS_TIM_CLEARINPUT_PRESCALER(sClearInputConfig->ClearInputPrescaler)); assert_param(IS_TIM_CLEARINPUT_FILTER(sClearInputConfig->ClearInputFilter)); TIM_ETR_SetConfig(htim->Instance, sClearInputConfig->ClearInputPrescaler, sClearInputConfig->ClearInputPolarity, sClearInputConfig->ClearInputFilter); } switch (Channel) { case TIM_CHANNEL_1: { if(sClearInputConfig->ClearInputState != RESET) { /* Enable the Ocref clear feature for Channel 1U */ htim->Instance->CCMR1 |= TIM_CCMR1_OC1CE; } else { /* Disable the Ocref clear feature for Channel 1U */ htim->Instance->CCMR1 &= ~TIM_CCMR1_OC1CE; } } break; case TIM_CHANNEL_2: { assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); if(sClearInputConfig->ClearInputState != RESET) { /* Enable the Ocref clear feature for Channel 2U */ htim->Instance->CCMR1 |= TIM_CCMR1_OC2CE; } else { /* Disable the Ocref clear feature for Channel 2U */ htim->Instance->CCMR1 &= ~TIM_CCMR1_OC2CE; } } break; case TIM_CHANNEL_3: { assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); if(sClearInputConfig->ClearInputState != RESET) { /* Enable the Ocref clear feature for Channel 3U */ htim->Instance->CCMR2 |= TIM_CCMR2_OC3CE; } else { /* Disable the Ocref clear feature for Channel 3U */ htim->Instance->CCMR2 &= ~TIM_CCMR2_OC3CE; } } break; case TIM_CHANNEL_4: { assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); if(sClearInputConfig->ClearInputState != RESET) { /* Enable the Ocref clear feature for Channel 4U */ htim->Instance->CCMR2 |= TIM_CCMR2_OC4CE; } else { /* Disable the Ocref clear feature for Channel 4U */ htim->Instance->CCMR2 &= ~TIM_CCMR2_OC4CE; } } break; default: break; } htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Configures the clock source to be used * @param htim TIM handle * @param sClockSourceConfig pointer to a TIM_ClockConfigTypeDef structure that * contains the clock source information for the TIM peripheral. * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_ConfigClockSource(TIM_HandleTypeDef *htim, TIM_ClockConfigTypeDef * sClockSourceConfig) { uint32_t tmpsmcr = 0U; /* Process Locked */ __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; /* Check the parameters */ assert_param(IS_TIM_CLOCKSOURCE(sClockSourceConfig->ClockSource)); /* Reset the SMS, TS, ECE, ETPS and ETRF bits */ tmpsmcr = htim->Instance->SMCR; tmpsmcr &= ~(TIM_SMCR_SMS | TIM_SMCR_TS); tmpsmcr &= ~(TIM_SMCR_ETF | TIM_SMCR_ETPS | TIM_SMCR_ECE | TIM_SMCR_ETP); htim->Instance->SMCR = tmpsmcr; switch (sClockSourceConfig->ClockSource) { case TIM_CLOCKSOURCE_INTERNAL: { assert_param(IS_TIM_INSTANCE(htim->Instance)); /* Disable slave mode to clock the prescaler directly with the internal clock */ htim->Instance->SMCR &= ~TIM_SMCR_SMS; } break; case TIM_CLOCKSOURCE_ETRMODE1: { /* Check whether or not the timer instance supports external trigger input mode 1 (ETRF)*/ assert_param(IS_TIM_CLOCKSOURCE_ETRMODE1_INSTANCE(htim->Instance)); /* Check ETR input conditioning related parameters */ assert_param(IS_TIM_CLOCKPRESCALER(sClockSourceConfig->ClockPrescaler)); assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); /* Configure the ETR Clock source */ TIM_ETR_SetConfig(htim->Instance, sClockSourceConfig->ClockPrescaler, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); /* Get the TIMx SMCR register value */ tmpsmcr = htim->Instance->SMCR; /* Reset the SMS and TS Bits */ tmpsmcr &= ~(TIM_SMCR_SMS | TIM_SMCR_TS); /* Select the External clock mode1 and the ETRF trigger */ tmpsmcr |= (TIM_SLAVEMODE_EXTERNAL1 | TIM_CLOCKSOURCE_ETRMODE1); /* Write to TIMx SMCR */ htim->Instance->SMCR = tmpsmcr; } break; case TIM_CLOCKSOURCE_ETRMODE2: { /* Check whether or not the timer instance supports external trigger input mode 2 (ETRF)*/ assert_param(IS_TIM_CLOCKSOURCE_ETRMODE2_INSTANCE(htim->Instance)); /* Check ETR input conditioning related parameters */ assert_param(IS_TIM_CLOCKPRESCALER(sClockSourceConfig->ClockPrescaler)); assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); /* Configure the ETR Clock source */ TIM_ETR_SetConfig(htim->Instance, sClockSourceConfig->ClockPrescaler, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); /* Enable the External clock mode2 */ htim->Instance->SMCR |= TIM_SMCR_ECE; } break; case TIM_CLOCKSOURCE_TI1: { /* Check whether or not the timer instance supports external clock mode 1U */ assert_param(IS_TIM_CLOCKSOURCE_TIX_INSTANCE(htim->Instance)); /* Check TI1 input conditioning related parameters */ assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); TIM_TI1_ConfigInputStage(htim->Instance, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI1); } break; case TIM_CLOCKSOURCE_TI2: { /* Check whether or not the timer instance supports external clock mode 1 (ETRF)*/ assert_param(IS_TIM_CLOCKSOURCE_TIX_INSTANCE(htim->Instance)); /* Check TI2 input conditioning related parameters */ assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); TIM_TI2_ConfigInputStage(htim->Instance, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI2); } break; case TIM_CLOCKSOURCE_TI1ED: { /* Check whether or not the timer instance supports external clock mode 1U */ assert_param(IS_TIM_CLOCKSOURCE_TIX_INSTANCE(htim->Instance)); /* Check TI1 input conditioning related parameters */ assert_param(IS_TIM_CLOCKPOLARITY(sClockSourceConfig->ClockPolarity)); assert_param(IS_TIM_CLOCKFILTER(sClockSourceConfig->ClockFilter)); TIM_TI1_ConfigInputStage(htim->Instance, sClockSourceConfig->ClockPolarity, sClockSourceConfig->ClockFilter); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_TI1ED); } break; case TIM_CLOCKSOURCE_ITR0: { /* Check whether or not the timer instance supports external clock mode 1U */ assert_param(IS_TIM_CLOCKSOURCE_ITRX_INSTANCE(htim->Instance)); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR0); } break; case TIM_CLOCKSOURCE_ITR1: { /* Check whether or not the timer instance supports external clock mode 1U */ assert_param(IS_TIM_CLOCKSOURCE_ITRX_INSTANCE(htim->Instance)); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR1); } break; case TIM_CLOCKSOURCE_ITR2: { /* Check whether or not the timer instance supports external clock mode 1U */ assert_param(IS_TIM_CLOCKSOURCE_ITRX_INSTANCE(htim->Instance)); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR2); } break; case TIM_CLOCKSOURCE_ITR3: { /* Check whether or not the timer instance supports external clock mode 1U */ assert_param(IS_TIM_CLOCKSOURCE_ITRX_INSTANCE(htim->Instance)); TIM_ITRx_SetConfig(htim->Instance, TIM_CLOCKSOURCE_ITR3); } break; default: break; } htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Selects the signal connected to the TI1 input: direct from CH1_input * or a XOR combination between CH1_input, CH2_input & CH3_input * @param htim TIM handle. * @param TI1_Selection: Indicate whether or not channel 1 is connected to the * output of a XOR gate. * This parameter can be one of the following values: * @arg TIM_TI1SELECTION_CH1: The TIMx_CH1 pin is connected to TI1 input * @arg TIM_TI1SELECTION_XORCOMBINATION: The TIMx_CH1, CH2 and CH3 * pins are connected to the TI1 input (XOR combination) * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_ConfigTI1Input(TIM_HandleTypeDef *htim, uint32_t TI1_Selection) { uint32_t tmpcr2 = 0U; /* Check the parameters */ assert_param(IS_TIM_XOR_INSTANCE(htim->Instance)); assert_param(IS_TIM_TI1SELECTION(TI1_Selection)); /* Get the TIMx CR2 register value */ tmpcr2 = htim->Instance->CR2; /* Reset the TI1 selection */ tmpcr2 &= ~TIM_CR2_TI1S; /* Set the the TI1 selection */ tmpcr2 |= TI1_Selection; /* Write to TIMxCR2 */ htim->Instance->CR2 = tmpcr2; return HAL_OK; } /** * @brief Configures the TIM in Slave mode * @param htim TIM handle. * @param sSlaveConfig pointer to a TIM_SlaveConfigTypeDef structure that * contains the selected trigger (internal trigger input, filtered * timer input or external trigger input) and the ) and the Slave * mode (Disable, Reset, Gated, Trigger, External clock mode 1). * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization(TIM_HandleTypeDef *htim, TIM_SlaveConfigTypeDef * sSlaveConfig) { /* Check the parameters */ assert_param(IS_TIM_SLAVE_INSTANCE(htim->Instance)); assert_param(IS_TIM_SLAVE_MODE(sSlaveConfig->SlaveMode)); assert_param(IS_TIM_TRIGGER_SELECTION(sSlaveConfig->InputTrigger)); __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; TIM_SlaveTimer_SetConfig(htim, sSlaveConfig); /* Disable Trigger Interrupt */ __HAL_TIM_DISABLE_IT(htim, TIM_IT_TRIGGER); /* Disable Trigger DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_TRIGGER); htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Configures the TIM in Slave mode in interrupt mode * @param htim TIM handle. * @param sSlaveConfig pointer to a TIM_SlaveConfigTypeDef structure that * contains the selected trigger (internal trigger input, filtered * timer input or external trigger input) and the ) and the Slave * mode (Disable, Reset, Gated, Trigger, External clock mode 1). * @retval HAL status */ HAL_StatusTypeDef HAL_TIM_SlaveConfigSynchronization_IT(TIM_HandleTypeDef *htim, TIM_SlaveConfigTypeDef * sSlaveConfig) { /* Check the parameters */ assert_param(IS_TIM_SLAVE_INSTANCE(htim->Instance)); assert_param(IS_TIM_SLAVE_MODE(sSlaveConfig->SlaveMode)); assert_param(IS_TIM_TRIGGER_SELECTION(sSlaveConfig->InputTrigger)); __HAL_LOCK(htim); htim->State = HAL_TIM_STATE_BUSY; TIM_SlaveTimer_SetConfig(htim, sSlaveConfig); /* Enable Trigger Interrupt */ __HAL_TIM_ENABLE_IT(htim, TIM_IT_TRIGGER); /* Disable Trigger DMA request */ __HAL_TIM_DISABLE_DMA(htim, TIM_DMA_TRIGGER); htim->State = HAL_TIM_STATE_READY; __HAL_UNLOCK(htim); return HAL_OK; } /** * @brief Read the captured value from Capture Compare unit * @param htim TIM handle. * @param Channel TIM Channels to be enabled * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 selected * @arg TIM_CHANNEL_2: TIM Channel 2 selected * @arg TIM_CHANNEL_3: TIM Channel 3 selected * @arg TIM_CHANNEL_4: TIM Channel 4 selected * @retval Captured value */ uint32_t HAL_TIM_ReadCapturedValue(TIM_HandleTypeDef *htim, uint32_t Channel) { uint32_t tmpreg = 0U; __HAL_LOCK(htim); switch (Channel) { case TIM_CHANNEL_1: { /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); /* Return the capture 1 value */ tmpreg = htim->Instance->CCR1; break; } case TIM_CHANNEL_2: { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); /* Return the capture 2 value */ tmpreg = htim->Instance->CCR2; break; } case TIM_CHANNEL_3: { /* Check the parameters */ assert_param(IS_TIM_CC3_INSTANCE(htim->Instance)); /* Return the capture 3 value */ tmpreg = htim->Instance->CCR3; break; } case TIM_CHANNEL_4: { /* Check the parameters */ assert_param(IS_TIM_CC4_INSTANCE(htim->Instance)); /* Return the capture 4 value */ tmpreg = htim->Instance->CCR4; break; } default: break; } __HAL_UNLOCK(htim); return tmpreg; } /** * @} */ /** @defgroup TIM_Exported_Functions_Group9 TIM Callbacks functions * @brief TIM Callbacks functions * @verbatim ============================================================================== ##### TIM Callbacks functions ##### ============================================================================== [..] This section provides TIM callback functions: (+) Timer Period elapsed callback (+) Timer Output Compare callback (+) Timer Input capture callback (+) Timer Trigger callback (+) Timer Error callback @endverbatim * @{ */ /** * @brief Period elapsed callback in non blocking mode * @param htim TIM handle * @retval None */ __weak void HAL_TIM_PeriodElapsedCallback(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the __HAL_TIM_PeriodElapsedCallback could be implemented in the user file */ } /** * @brief Output Compare callback in non blocking mode * @param htim TIM OC handle * @retval None */ __weak void HAL_TIM_OC_DelayElapsedCallback(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the __HAL_TIM_OC_DelayElapsedCallback could be implemented in the user file */ } /** * @brief Input Capture callback in non blocking mode * @param htim TIM IC handle * @retval None */ __weak void HAL_TIM_IC_CaptureCallback(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the __HAL_TIM_IC_CaptureCallback could be implemented in the user file */ } /** * @brief PWM Pulse finished callback in non blocking mode * @param htim TIM handle * @retval None */ __weak void HAL_TIM_PWM_PulseFinishedCallback(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the __HAL_TIM_PWM_PulseFinishedCallback could be implemented in the user file */ } /** * @brief Hall Trigger detection callback in non blocking mode * @param htim TIM handle * @retval None */ __weak void HAL_TIM_TriggerCallback(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_TriggerCallback could be implemented in the user file */ } /** * @brief Timer error callback in non blocking mode * @param htim TIM handle * @retval None */ __weak void HAL_TIM_ErrorCallback(TIM_HandleTypeDef *htim) { /* Prevent unused argument(s) compilation warning */ UNUSED(htim); /* NOTE : This function Should not be modified, when the callback is needed, the HAL_TIM_ErrorCallback could be implemented in the user file */ } /** * @} */ /** @defgroup TIM_Exported_Functions_Group10 Peripheral State functions * @brief Peripheral State functions * @verbatim ============================================================================== ##### Peripheral State functions ##### ============================================================================== [..] This subsection permit to get in run-time the status of the peripheral and the data flow. @endverbatim * @{ */ /** * @brief Return the TIM Base state * @param htim TIM Base handle * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIM_Base_GetState(TIM_HandleTypeDef *htim) { return htim->State; } /** * @brief Return the TIM OC state * @param htim TIM Ouput Compare handle * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIM_OC_GetState(TIM_HandleTypeDef *htim) { return htim->State; } /** * @brief Return the TIM PWM state * @param htim TIM handle * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIM_PWM_GetState(TIM_HandleTypeDef *htim) { return htim->State; } /** * @brief Return the TIM Input Capture state * @param htim TIM IC handle * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIM_IC_GetState(TIM_HandleTypeDef *htim) { return htim->State; } /** * @brief Return the TIM One Pulse Mode state * @param htim TIM OPM handle * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIM_OnePulse_GetState(TIM_HandleTypeDef *htim) { return htim->State; } /** * @brief Return the TIM Encoder Mode state * @param htim TIM Encoder handle * @retval HAL state */ HAL_TIM_StateTypeDef HAL_TIM_Encoder_GetState(TIM_HandleTypeDef *htim) { return htim->State; } /** * @} */ /** * @} */ /** @addtogroup TIM_Private_Functions TIM_Private_Functions * @{ */ /** * @brief TIM DMA error callback * @param hdma pointer to DMA handle. * @retval None */ void TIM_DMAError(DMA_HandleTypeDef *hdma) { TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; htim->State= HAL_TIM_STATE_READY; HAL_TIM_ErrorCallback(htim); } /** * @brief TIM DMA Delay Pulse complete callback. * @param hdma pointer to DMA handle. * @retval None */ void TIM_DMADelayPulseCplt(DMA_HandleTypeDef *hdma) { TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; htim->State= HAL_TIM_STATE_READY; if (hdma == htim->hdma[TIM_DMA_ID_CC1]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1; } else if (hdma == htim->hdma[TIM_DMA_ID_CC2]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2; } else if (hdma == htim->hdma[TIM_DMA_ID_CC3]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3; } else if (hdma == htim->hdma[TIM_DMA_ID_CC4]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4; } HAL_TIM_PWM_PulseFinishedCallback(htim); htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } /** * @brief TIM DMA Capture complete callback. * @param hdma pointer to DMA handle. * @retval None */ void TIM_DMACaptureCplt(DMA_HandleTypeDef *hdma) { TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; htim->State= HAL_TIM_STATE_READY; if (hdma == htim->hdma[TIM_DMA_ID_CC1]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_1; } else if (hdma == htim->hdma[TIM_DMA_ID_CC2]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_2; } else if (hdma == htim->hdma[TIM_DMA_ID_CC3]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_3; } else if (hdma == htim->hdma[TIM_DMA_ID_CC4]) { htim->Channel = HAL_TIM_ACTIVE_CHANNEL_4; } HAL_TIM_IC_CaptureCallback(htim); htim->Channel = HAL_TIM_ACTIVE_CHANNEL_CLEARED; } /** * @brief TIM DMA Period Elapse complete callback. * @param hdma pointer to DMA handle. * @retval None */ static void TIM_DMAPeriodElapsedCplt(DMA_HandleTypeDef *hdma) { TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; htim->State= HAL_TIM_STATE_READY; HAL_TIM_PeriodElapsedCallback(htim); } /** * @brief TIM DMA Trigger callback. * @param hdma pointer to DMA handle. * @retval None */ static void TIM_DMATriggerCplt(DMA_HandleTypeDef *hdma) { TIM_HandleTypeDef* htim = ( TIM_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; htim->State= HAL_TIM_STATE_READY; HAL_TIM_TriggerCallback(htim); } /** * @brief Time Base configuration * @param TIMx TIM periheral * @param Structure TIM Base configuration structure * @retval None */ void TIM_Base_SetConfig(TIM_TypeDef *TIMx, TIM_Base_InitTypeDef *Structure) { uint32_t tmpcr1 = 0U; tmpcr1 = TIMx->CR1; /* Set TIM Time Base Unit parameters ---------------------------------------*/ if (IS_TIM_COUNTER_MODE_SELECT_INSTANCE(TIMx)) { /* Select the Counter Mode */ tmpcr1 &= ~(TIM_CR1_DIR | TIM_CR1_CMS); tmpcr1 |= Structure->CounterMode; } if(IS_TIM_CLOCK_DIVISION_INSTANCE(TIMx)) { /* Set the clock division */ tmpcr1 &= ~TIM_CR1_CKD; tmpcr1 |= (uint32_t)Structure->ClockDivision; } /* Set the auto-reload preload */ MODIFY_REG(tmpcr1, TIM_CR1_ARPE, Structure->AutoReloadPreload); TIMx->CR1 = tmpcr1; /* Set the Autoreload value */ TIMx->ARR = (uint32_t)Structure->Period ; /* Set the Prescaler value */ TIMx->PSC = (uint32_t)Structure->Prescaler; if (IS_TIM_REPETITION_COUNTER_INSTANCE(TIMx)) { /* Set the Repetition Counter value */ TIMx->RCR = Structure->RepetitionCounter; } /* Generate an update event to reload the Prescaler and the repetition counter(only for TIM1 and TIM8) value immediatly */ TIMx->EGR = TIM_EGR_UG; } /** * @brief Time Ouput Compare 1 configuration * @param TIMx to select the TIM peripheral * @param OC_Config The ouput configuration structure * @retval None */ void TIM_OC1_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config) { uint32_t tmpccmrx = 0U; uint32_t tmpccer = 0U; uint32_t tmpcr2 = 0U; /* Disable the Channel 1: Reset the CC1E Bit */ TIMx->CCER &= ~TIM_CCER_CC1E; /* Get the TIMx CCER register value */ tmpccer = TIMx->CCER; /* Get the TIMx CR2 register value */ tmpcr2 = TIMx->CR2; /* Get the TIMx CCMR1 register value */ tmpccmrx = TIMx->CCMR1; /* Reset the Output Compare Mode Bits */ tmpccmrx &= ~TIM_CCMR1_OC1M; tmpccmrx &= ~TIM_CCMR1_CC1S; /* Select the Output Compare Mode */ tmpccmrx |= OC_Config->OCMode; /* Reset the Output Polarity level */ tmpccer &= ~TIM_CCER_CC1P; /* Set the Output Compare Polarity */ tmpccer |= OC_Config->OCPolarity; if(IS_TIM_CCXN_INSTANCE(TIMx, TIM_CHANNEL_1)) { /* Check parameters */ assert_param(IS_TIM_OCN_POLARITY(OC_Config->OCNPolarity)); /* Reset the Output N Polarity level */ tmpccer &= ~TIM_CCER_CC1NP; /* Set the Output N Polarity */ tmpccer |= OC_Config->OCNPolarity; /* Reset the Output N State */ tmpccer &= ~TIM_CCER_CC1NE; } if(IS_TIM_BREAK_INSTANCE(TIMx)) { /* Check parameters */ assert_param(IS_TIM_OCNIDLE_STATE(OC_Config->OCNIdleState)); assert_param(IS_TIM_OCIDLE_STATE(OC_Config->OCIdleState)); /* Reset the Output Compare and Output Compare N IDLE State */ tmpcr2 &= ~TIM_CR2_OIS1; tmpcr2 &= ~TIM_CR2_OIS1N; /* Set the Output Idle state */ tmpcr2 |= OC_Config->OCIdleState; /* Set the Output N Idle state */ tmpcr2 |= OC_Config->OCNIdleState; } /* Write to TIMx CR2 */ TIMx->CR2 = tmpcr2; /* Write to TIMx CCMR1 */ TIMx->CCMR1 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCR1 = OC_Config->Pulse; /* Write to TIMx CCER */ TIMx->CCER = tmpccer; } /** * @brief Time Ouput Compare 2 configuration * @param TIMx to select the TIM peripheral * @param OC_Config The ouput configuration structure * @retval None */ void TIM_OC2_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config) { uint32_t tmpccmrx = 0U; uint32_t tmpccer = 0U; uint32_t tmpcr2 = 0U; /* Disable the Channel 2: Reset the CC2E Bit */ TIMx->CCER &= ~TIM_CCER_CC2E; /* Get the TIMx CCER register value */ tmpccer = TIMx->CCER; /* Get the TIMx CR2 register value */ tmpcr2 = TIMx->CR2; /* Get the TIMx CCMR1 register value */ tmpccmrx = TIMx->CCMR1; /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= ~TIM_CCMR1_OC2M; tmpccmrx &= ~TIM_CCMR1_CC2S; /* Select the Output Compare Mode */ tmpccmrx |= (OC_Config->OCMode << 8U); /* Reset the Output Polarity level */ tmpccer &= ~TIM_CCER_CC2P; /* Set the Output Compare Polarity */ tmpccer |= (OC_Config->OCPolarity << 4U); if(IS_TIM_CCXN_INSTANCE(TIMx, TIM_CHANNEL_2)) { assert_param(IS_TIM_OCN_POLARITY(OC_Config->OCNPolarity)); /* Reset the Output N Polarity level */ tmpccer &= ~TIM_CCER_CC2NP; /* Set the Output N Polarity */ tmpccer |= (OC_Config->OCNPolarity << 4U); /* Reset the Output N State */ tmpccer &= ~TIM_CCER_CC2NE; } if(IS_TIM_BREAK_INSTANCE(TIMx)) { /* Check parameters */ assert_param(IS_TIM_OCNIDLE_STATE(OC_Config->OCNIdleState)); assert_param(IS_TIM_OCIDLE_STATE(OC_Config->OCIdleState)); /* Reset the Output Compare IDLE State */ tmpcr2 &= ~TIM_CR2_OIS2; #if defined(STM32F373xC) || defined(STM32F378xx) #else /* Reset the Output Compare N IDLE State */ tmpcr2 &= ~TIM_CR2_OIS2N; #endif /* Set the Output Idle state */ tmpcr2 |= (OC_Config->OCIdleState << 2U); /* Set the Output N Idle state */ tmpcr2 |= (OC_Config->OCNIdleState << 2U); } /* Write to TIMx CR2 */ TIMx->CR2 = tmpcr2; /* Write to TIMx CCMR1 */ TIMx->CCMR1 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCR2 = OC_Config->Pulse; /* Write to TIMx CCER */ TIMx->CCER = tmpccer; } /** * @brief Time Ouput Compare 3 configuration * @param TIMx to select the TIM peripheral * @param OC_Config The ouput configuration structure * @retval None */ void TIM_OC3_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config) { uint32_t tmpccmrx = 0U; uint32_t tmpccer = 0U; uint32_t tmpcr2 = 0U; /* Disable the Channel 3: Reset the CC2E Bit */ TIMx->CCER &= ~TIM_CCER_CC3E; /* Get the TIMx CCER register value */ tmpccer = TIMx->CCER; /* Get the TIMx CR2 register value */ tmpcr2 = TIMx->CR2; /* Get the TIMx CCMR2 register value */ tmpccmrx = TIMx->CCMR2; /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= ~TIM_CCMR2_OC3M; tmpccmrx &= ~TIM_CCMR2_CC3S; /* Select the Output Compare Mode */ tmpccmrx |= OC_Config->OCMode; /* Reset the Output Polarity level */ tmpccer &= ~TIM_CCER_CC3P; /* Set the Output Compare Polarity */ tmpccer |= (OC_Config->OCPolarity << 8U); if(IS_TIM_CCXN_INSTANCE(TIMx, TIM_CHANNEL_3)) { assert_param(IS_TIM_OCN_POLARITY(OC_Config->OCNPolarity)); /* Reset the Output N Polarity level */ tmpccer &= ~TIM_CCER_CC3NP; /* Set the Output N Polarity */ tmpccer |= (OC_Config->OCNPolarity << 8U); /* Reset the Output N State */ tmpccer &= ~TIM_CCER_CC3NE; } if(IS_TIM_BREAK_INSTANCE(TIMx)) { /* Check parameters */ assert_param(IS_TIM_OCNIDLE_STATE(OC_Config->OCNIdleState)); assert_param(IS_TIM_OCIDLE_STATE(OC_Config->OCIdleState)); #if defined(STM32F373xC) || defined(STM32F378xx) #else /* Reset the Output Compare and Output Compare N IDLE State */ tmpcr2 &= ~TIM_CR2_OIS3; tmpcr2 &= ~TIM_CR2_OIS3N; #endif /* Set the Output Idle state */ tmpcr2 |= (OC_Config->OCIdleState << 4U); /* Set the Output N Idle state */ tmpcr2 |= (OC_Config->OCNIdleState << 4U); } /* Write to TIMx CR2 */ TIMx->CR2 = tmpcr2; /* Write to TIMx CCMR2 */ TIMx->CCMR2 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCR3 = OC_Config->Pulse; /* Write to TIMx CCER */ TIMx->CCER = tmpccer; } /** * @brief Time Ouput Compare 4 configuration * @param TIMx to select the TIM peripheral * @param OC_Config The ouput configuration structure * @retval None */ void TIM_OC4_SetConfig(TIM_TypeDef *TIMx, TIM_OC_InitTypeDef *OC_Config) { uint32_t tmpccmrx = 0U; uint32_t tmpccer = 0U; uint32_t tmpcr2 = 0U; /* Disable the Channel 4: Reset the CC4E Bit */ TIMx->CCER &= ~TIM_CCER_CC4E; /* Get the TIMx CCER register value */ tmpccer = TIMx->CCER; /* Get the TIMx CR2 register value */ tmpcr2 = TIMx->CR2; /* Get the TIMx CCMR2 register value */ tmpccmrx = TIMx->CCMR2; /* Reset the Output Compare mode and Capture/Compare selection Bits */ tmpccmrx &= ~TIM_CCMR2_OC4M; tmpccmrx &= ~TIM_CCMR2_CC4S; /* Select the Output Compare Mode */ tmpccmrx |= (OC_Config->OCMode << 8U); /* Reset the Output Polarity level */ tmpccer &= ~TIM_CCER_CC4P; /* Set the Output Compare Polarity */ tmpccer |= (OC_Config->OCPolarity << 12U); if(IS_TIM_BREAK_INSTANCE(TIMx)) { assert_param(IS_TIM_OCIDLE_STATE(OC_Config->OCIdleState)); #if defined(STM32F373xC) || defined(STM32F378xx) #else /* Reset the Output Compare IDLE State */ tmpcr2 &= ~TIM_CR2_OIS4; #endif /* Set the Output Idle state */ tmpcr2 |= (OC_Config->OCIdleState << 6U); } /* Write to TIMx CR2 */ TIMx->CR2 = tmpcr2; /* Write to TIMx CCMR2 */ TIMx->CCMR2 = tmpccmrx; /* Set the Capture Compare Register value */ TIMx->CCR4 = OC_Config->Pulse; /* Write to TIMx CCER */ TIMx->CCER = tmpccer; } static void TIM_SlaveTimer_SetConfig(TIM_HandleTypeDef *htim, TIM_SlaveConfigTypeDef * sSlaveConfig) { uint32_t tmpsmcr = 0U; uint32_t tmpccmr1 = 0U; uint32_t tmpccer = 0U; /* Get the TIMx SMCR register value */ tmpsmcr = htim->Instance->SMCR; /* Reset the Trigger Selection Bits */ tmpsmcr &= ~TIM_SMCR_TS; /* Set the Input Trigger source */ tmpsmcr |= sSlaveConfig->InputTrigger; /* Reset the slave mode Bits */ tmpsmcr &= ~TIM_SMCR_SMS; /* Set the slave mode */ tmpsmcr |= sSlaveConfig->SlaveMode; /* Write to TIMx SMCR */ htim->Instance->SMCR = tmpsmcr; /* Configure the trigger prescaler, filter, and polarity */ switch (sSlaveConfig->InputTrigger) { case TIM_TS_ETRF: { /* Check the parameters */ assert_param(IS_TIM_CLOCKSOURCE_ETRMODE1_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRIGGERPRESCALER(sSlaveConfig->TriggerPrescaler)); assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity)); assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter)); /* Configure the ETR Trigger source */ TIM_ETR_SetConfig(htim->Instance, sSlaveConfig->TriggerPrescaler, sSlaveConfig->TriggerPolarity, sSlaveConfig->TriggerFilter); } break; case TIM_TS_TI1F_ED: { /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter)); /* Disable the Channel 1: Reset the CC1E Bit */ tmpccer = htim->Instance->CCER; htim->Instance->CCER &= ~TIM_CCER_CC1E; tmpccmr1 = htim->Instance->CCMR1; /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC1F; tmpccmr1 |= ((sSlaveConfig->TriggerFilter) << 4U); /* Write to TIMx CCMR1 and CCER registers */ htim->Instance->CCMR1 = tmpccmr1; htim->Instance->CCER = tmpccer; } break; case TIM_TS_TI1FP1: { /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity)); assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter)); /* Configure TI1 Filter and Polarity */ TIM_TI1_ConfigInputStage(htim->Instance, sSlaveConfig->TriggerPolarity, sSlaveConfig->TriggerFilter); } break; case TIM_TS_TI2FP2: { /* Check the parameters */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); assert_param(IS_TIM_TRIGGERPOLARITY(sSlaveConfig->TriggerPolarity)); assert_param(IS_TIM_TRIGGERFILTER(sSlaveConfig->TriggerFilter)); /* Configure TI2 Filter and Polarity */ TIM_TI2_ConfigInputStage(htim->Instance, sSlaveConfig->TriggerPolarity, sSlaveConfig->TriggerFilter); } break; case TIM_TS_ITR0: { /* Check the parameter */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); } break; case TIM_TS_ITR1: { /* Check the parameter */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); } break; case TIM_TS_ITR2: { /* Check the parameter */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); } break; case TIM_TS_ITR3: { /* Check the parameter */ assert_param(IS_TIM_CC2_INSTANCE(htim->Instance)); } break; default: break; } } /** * @brief Configure the TI1 as Input. * @param TIMx to select the TIM peripheral. * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_ICPOLARITY_RISING * @arg TIM_ICPOLARITY_FALLING * @arg TIM_ICPOLARITY_BOTHEDGE * @param TIM_ICSelection specifies the input to be used. * This parameter can be one of the following values: * @arg TIM_ICSELECTION_DIRECTTI: TIM Input 1 is selected to be connected to IC1. * @arg TIM_ICSELECTION_INDIRECTTI: TIM Input 1 is selected to be connected to IC2. * @arg TIM_ICSELECTION_TRC: TIM Input 1 is selected to be connected to TRC. * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @retval None * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI2FP1 * (on channel2 path) is used as the input signal. Therefore CCMR1 must be * protected against un-initialized filter and polarity values. */ void TIM_TI1_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter) { uint32_t tmpccmr1 = 0U; uint32_t tmpccer = 0U; /* Disable the Channel 1: Reset the CC1E Bit */ TIMx->CCER &= ~TIM_CCER_CC1E; tmpccmr1 = TIMx->CCMR1; tmpccer = TIMx->CCER; /* Select the Input */ if(IS_TIM_CC2_INSTANCE(TIMx) != RESET) { tmpccmr1 &= ~TIM_CCMR1_CC1S; tmpccmr1 |= TIM_ICSelection; } else { tmpccmr1 |= TIM_CCMR1_CC1S_0; } /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC1F; tmpccmr1 |= ((TIM_ICFilter << 4U) & TIM_CCMR1_IC1F); /* Select the Polarity and set the CC1E Bit */ tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC1NP); tmpccer |= (TIM_ICPolarity & (TIM_CCER_CC1P | TIM_CCER_CC1NP)); /* Write to TIMx CCMR1 and CCER registers */ TIMx->CCMR1 = tmpccmr1; TIMx->CCER = tmpccer; } /** * @brief Configure the Polarity and Filter for TI1. * @param TIMx to select the TIM peripheral. * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_ICPOLARITY_RISING * @arg TIM_ICPOLARITY_FALLING * @arg TIM_ICPOLARITY_BOTHEDGE * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @retval None */ static void TIM_TI1_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter) { uint32_t tmpccmr1 = 0U; uint32_t tmpccer = 0U; /* Disable the Channel 1: Reset the CC1E Bit */ tmpccer = TIMx->CCER; TIMx->CCER &= ~TIM_CCER_CC1E; tmpccmr1 = TIMx->CCMR1; /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC1F; tmpccmr1 |= (TIM_ICFilter << 4U); /* Select the Polarity and set the CC1E Bit */ tmpccer &= ~(TIM_CCER_CC1P | TIM_CCER_CC1NP); tmpccer |= TIM_ICPolarity; /* Write to TIMx CCMR1 and CCER registers */ TIMx->CCMR1 = tmpccmr1; TIMx->CCER = tmpccer; } /** * @brief Configure the TI2 as Input. * @param TIMx to select the TIM peripheral * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_ICPOLARITY_RISING * @arg TIM_ICPOLARITY_FALLING * @arg TIM_ICPOLARITY_BOTHEDGE * @param TIM_ICSelection specifies the input to be used. * This parameter can be one of the following values: * @arg TIM_ICSELECTION_DIRECTTI: TIM Input 2 is selected to be connected to IC2. * @arg TIM_ICSELECTION_INDIRECTTI: TIM Input 2 is selected to be connected to IC1. * @arg TIM_ICSELECTION_TRC: TIM Input 2 is selected to be connected to TRC. * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @retval None * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI1FP2 * (on channel1 path) is used as the input signal. Therefore CCMR1 must be * protected against un-initialized filter and polarity values. */ static void TIM_TI2_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter) { uint32_t tmpccmr1 = 0U; uint32_t tmpccer = 0U; /* Disable the Channel 2: Reset the CC2E Bit */ TIMx->CCER &= ~TIM_CCER_CC2E; tmpccmr1 = TIMx->CCMR1; tmpccer = TIMx->CCER; /* Select the Input */ tmpccmr1 &= ~TIM_CCMR1_CC2S; tmpccmr1 |= (TIM_ICSelection << 8U); /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC2F; tmpccmr1 |= ((TIM_ICFilter << 12U) & TIM_CCMR1_IC2F); /* Select the Polarity and set the CC2E Bit */ tmpccer &= ~(TIM_CCER_CC2P | TIM_CCER_CC2NP); tmpccer |= ((TIM_ICPolarity << 4U) & (TIM_CCER_CC2P | TIM_CCER_CC2NP)); /* Write to TIMx CCMR1 and CCER registers */ TIMx->CCMR1 = tmpccmr1 ; TIMx->CCER = tmpccer; } /** * @brief Configure the Polarity and Filter for TI2. * @param TIMx to select the TIM peripheral. * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_ICPOLARITY_RISING * @arg TIM_ICPOLARITY_FALLING * @arg TIM_ICPOLARITY_BOTHEDGE * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @retval None */ static void TIM_TI2_ConfigInputStage(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICFilter) { uint32_t tmpccmr1 = 0U; uint32_t tmpccer = 0U; /* Disable the Channel 2: Reset the CC2E Bit */ TIMx->CCER &= ~TIM_CCER_CC2E; tmpccmr1 = TIMx->CCMR1; tmpccer = TIMx->CCER; /* Set the filter */ tmpccmr1 &= ~TIM_CCMR1_IC2F; tmpccmr1 |= (TIM_ICFilter << 12U); /* Select the Polarity and set the CC2E Bit */ tmpccer &= ~(TIM_CCER_CC2P | TIM_CCER_CC2NP); tmpccer |= (TIM_ICPolarity << 4U); /* Write to TIMx CCMR1 and CCER registers */ TIMx->CCMR1 = tmpccmr1 ; TIMx->CCER = tmpccer; } /** * @brief Configure the TI3 as Input. * @param TIMx to select the TIM peripheral * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_ICPOLARITY_RISING * @arg TIM_ICPOLARITY_FALLING * @arg TIM_ICPOLARITY_BOTHEDGE * @param TIM_ICSelection specifies the input to be used. * This parameter can be one of the following values: * @arg TIM_ICSELECTION_DIRECTTI: TIM Input 3 is selected to be connected to IC3. * @arg TIM_ICSELECTION_INDIRECTTI: TIM Input 3 is selected to be connected to IC4. * @arg TIM_ICSELECTION_TRC: TIM Input 3 is selected to be connected to TRC. * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @retval None * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI3FP4 * (on channel1 path) is used as the input signal. Therefore CCMR2 must be * protected against un-initialized filter and polarity values. */ static void TIM_TI3_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter) { uint32_t tmpccmr2 = 0U; uint32_t tmpccer = 0U; /* Disable the Channel 3: Reset the CC3E Bit */ TIMx->CCER &= ~TIM_CCER_CC3E; tmpccmr2 = TIMx->CCMR2; tmpccer = TIMx->CCER; /* Select the Input */ tmpccmr2 &= ~TIM_CCMR2_CC3S; tmpccmr2 |= TIM_ICSelection; /* Set the filter */ tmpccmr2 &= ~TIM_CCMR2_IC3F; tmpccmr2 |= ((TIM_ICFilter << 4U) & TIM_CCMR2_IC3F); /* Select the Polarity and set the CC3E Bit */ tmpccer &= ~(TIM_CCER_CC3P | TIM_CCER_CC3NP); tmpccer |= ((TIM_ICPolarity << 8U) & (TIM_CCER_CC3P | TIM_CCER_CC3NP)); /* Write to TIMx CCMR2 and CCER registers */ TIMx->CCMR2 = tmpccmr2; TIMx->CCER = tmpccer; } /** * @brief Configure the TI4 as Input. * @param TIMx to select the TIM peripheral * @param TIM_ICPolarity The Input Polarity. * This parameter can be one of the following values: * @arg TIM_ICPOLARITY_RISING * @arg TIM_ICPOLARITY_FALLING * @arg TIM_ICPOLARITY_BOTHEDGE * @param TIM_ICSelection specifies the input to be used. * This parameter can be one of the following values: * @arg TIM_ICSELECTION_DIRECTTI: TIM Input 4 is selected to be connected to IC4. * @arg TIM_ICSELECTION_INDIRECTTI: TIM Input 4 is selected to be connected to IC3. * @arg TIM_ICSELECTION_TRC: TIM Input 4 is selected to be connected to TRC. * @param TIM_ICFilter Specifies the Input Capture Filter. * This parameter must be a value between 0x00 and 0x0F. * @note TIM_ICFilter and TIM_ICPolarity are not used in INDIRECT mode as TI4FP3 * (on channel1 path) is used as the input signal. Therefore CCMR2 must be * protected against un-initialized filter and polarity values. * @retval None */ static void TIM_TI4_SetConfig(TIM_TypeDef *TIMx, uint32_t TIM_ICPolarity, uint32_t TIM_ICSelection, uint32_t TIM_ICFilter) { uint32_t tmpccmr2 = 0U; uint32_t tmpccer = 0U; /* Disable the Channel 4: Reset the CC4E Bit */ TIMx->CCER &= ~TIM_CCER_CC4E; tmpccmr2 = TIMx->CCMR2; tmpccer = TIMx->CCER; /* Select the Input */ tmpccmr2 &= ~TIM_CCMR2_CC4S; tmpccmr2 |= (TIM_ICSelection << 8U); /* Set the filter */ tmpccmr2 &= ~TIM_CCMR2_IC4F; tmpccmr2 |= ((TIM_ICFilter << 12U) & TIM_CCMR2_IC4F); /* Select the Polarity and set the CC4E Bit */ tmpccer &= ~(TIM_CCER_CC4P | TIM_CCER_CC4NP); tmpccer |= ((TIM_ICPolarity << 12U) & (TIM_CCER_CC4P | TIM_CCER_CC4NP)); /* Write to TIMx CCMR2 and CCER registers */ TIMx->CCMR2 = tmpccmr2; TIMx->CCER = tmpccer ; } /** * @brief Selects the Input Trigger source * @param TIMx to select the TIM peripheral * @param InputTriggerSource The Input Trigger source. * This parameter can be one of the following values: * @arg TIM_TS_ITR0: Internal Trigger 0 * @arg TIM_TS_ITR1: Internal Trigger 1 * @arg TIM_TS_ITR2: Internal Trigger 2 * @arg TIM_TS_ITR3: Internal Trigger 3 * @arg TIM_TS_TI1F_ED: TI1 Edge Detector * @arg TIM_TS_TI1FP1: Filtered Timer Input 1 * @arg TIM_TS_TI2FP2: Filtered Timer Input 2 * @arg TIM_TS_ETRF: External Trigger input * @retval None */ static void TIM_ITRx_SetConfig(TIM_TypeDef *TIMx, uint16_t InputTriggerSource) { uint32_t tmpsmcr = 0U; /* Get the TIMx SMCR register value */ tmpsmcr = TIMx->SMCR; /* Reset the TS Bits */ tmpsmcr &= ~TIM_SMCR_TS; /* Set the Input Trigger source and the slave mode*/ tmpsmcr |= InputTriggerSource | TIM_SLAVEMODE_EXTERNAL1; /* Write to TIMx SMCR */ TIMx->SMCR = tmpsmcr; } /** * @brief Configures the TIMx External Trigger (ETR). * @param TIMx to select the TIM peripheral * @param TIM_ExtTRGPrescaler The external Trigger Prescaler. * This parameter can be one of the following values: * @arg TIM_ETRPRESCALER_DIV1 : ETRP Prescaler OFF. * @arg TIM_ETRPRESCALER_DIV2 : ETRP frequency divided by 2. * @arg TIM_ETRPRESCALER_DIV4 : ETRP frequency divided by 4. * @arg TIM_ETRPRESCALER_DIV8 : ETRP frequency divided by 8. * @param TIM_ExtTRGPolarity The external Trigger Polarity. * This parameter can be one of the following values: * @arg TIM_ETRPOLARITY_INVERTED : active low or falling edge active. * @arg TIM_ETRPOLARITY_NONINVERTED : active high or rising edge active. * @param ExtTRGFilter External Trigger Filter. * This parameter must be a value between 0x00 and 0x0F * @retval None */ void TIM_ETR_SetConfig(TIM_TypeDef* TIMx, uint32_t TIM_ExtTRGPrescaler, uint32_t TIM_ExtTRGPolarity, uint32_t ExtTRGFilter) { uint32_t tmpsmcr = 0U; tmpsmcr = TIMx->SMCR; /* Reset the ETR Bits */ tmpsmcr &= ~(TIM_SMCR_ETF | TIM_SMCR_ETPS | TIM_SMCR_ECE | TIM_SMCR_ETP); /* Set the Prescaler, the Filter value and the Polarity */ tmpsmcr |= (uint32_t)(TIM_ExtTRGPrescaler | (TIM_ExtTRGPolarity | (ExtTRGFilter << 8U))); /* Write to TIMx SMCR */ TIMx->SMCR = tmpsmcr; } /** * @brief Enables or disables the TIM Capture Compare Channel x. * @param TIMx to select the TIM peripheral * @param Channel specifies the TIM Channel * This parameter can be one of the following values: * @arg TIM_CHANNEL_1: TIM Channel 1 * @arg TIM_CHANNEL_2: TIM Channel 2 * @arg TIM_CHANNEL_3: TIM Channel 3 * @arg TIM_CHANNEL_4: TIM Channel 4 * @param ChannelState specifies the TIM Channel CCxE bit new state. * This parameter can be: TIM_CCx_ENABLE or TIM_CCx_Disable. * @retval None */ void TIM_CCxChannelCmd(TIM_TypeDef* TIMx, uint32_t Channel, uint32_t ChannelState) { uint32_t tmp = 0U; /* Check the parameters */ assert_param(IS_TIM_CC1_INSTANCE(TIMx)); assert_param(IS_TIM_CHANNELS(Channel)); tmp = TIM_CCER_CC1E << Channel; /* Reset the CCxE Bit */ TIMx->CCER &= ~tmp; /* Set or reset the CCxE Bit */ TIMx->CCER |= (uint32_t)(ChannelState << Channel); } /** * @} */ #endif /* HAL_TIM_MODULE_ENABLED */ /** * @} */ /** * @} */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/